The short-wave infrared (SWIR) wavelength, especially 1.55 μm, has attracted significant attention in various areas such as high-speed optical communication and LiDAR systems. Avalanche photodiodes (APDs) are a critical component as a receiver in these systems due to their internal gain, which enhances the system performance. Silicon-based APDs are promising since they are CMOS compatible, but they are limited in detecting 1.55 μm light detection. This study proposes a p-type Si on n-type GaAs0.51Sb0.49 (GaAsSb) lattice matched to InP substrates heterojunction formed using a grafting technique for future GaAsSb/Si APD technology. A p+Si nanomembrane is transferred onto the GaAsSb/AlInAs/InP substrate, with an ultrathin ALD-Al2O3 oxide at the interface, which behaves as both double-side passivation and quantum tunneling layers. The devices exhibit excellent surface morphology and interface quality, confirmed by atomic force microscope and transmission electron microscope. Also, the current–voltage (I–V) of the p+Si/n−GaAsSb heterojunction shows the rectifying characteristics with an ideality factor of 1.8. The I–V tests across multiple devices confirm high consistency and yield. Furthermore, the x-ray photoelectron spectroscopy measurement reveals that GaAsSb and Si are found to have type-II band alignment with a conduction band offset of 50 meV, which is favorable for the high-bandwidth APD application. The demonstration of the GaAsSb/Si heterojunction highlights the potential to advance current SWIR PD technologies.
For short-wavelength infrared (SWIR) avalanche photodiodes, a separate absorption, charge, and multiplication design is widely used. AlInAsSb on an InP substrate is a potential multiplication layer with a lattice match to absorber candidates across the SWIR. Our new measurements demonstrate that AlInAsSb on InP is a promising multiplier candidate with a relatively low dark current density of 10−4 A/cm2 at a gain of 30; a high gain, measured up to 245 in this study; and a large differentiation of electron and hole ionization leading to a low excess noise, measured to be 2.5 at a gain of 30. These characteristics are all improvements over commercially available SWIR detectors incorporating InAlAs or InP as the multiplier. We measured and analyzed gain for multiple wavelengths to extract the ionization coefficients as a function of an electric field over the range 0.33–0.6 MV/cm.
There is increased interest in the heterogeneous integration of various compound semiconductors with Si for a variety of electronic and photonic applications. This paper focuses on integrating GaAsSb (with absorption in the C-band at 1550 nm) with silicon to fabricate photodiodes, leveraging epitaxial layer transfer (ELT) methods. Two ELT techniques—nanomembrane transfer printing and macro-transfer printing—are compared for transferring GaAsSb films from InP substrates to Si, forming PIN diodes. Characterization through atomic force microscopy and transmission electron microscopy exhibits a high-quality, defect-free interface. Current–voltage (IV) measurements and capacitance–voltage analysis validate the quality and functionality of the heterostructures. Photocurrent measurements at room temperature and 200 K demonstrate the device's photo-response at 1.55 μm, highlighting the presence of an active interface.
A minority carrier lifetime of 2.7 ns is measured at 77 K for a GeSn/SiGeSn single quantum well using time-resolved photoluminescence, and subsequent analyses indicate that the lifetime is Auger-limited. The 77 K lifetime is evaluated as a function of stepwise dose of 63 MeV proton irradiation up to a fluence of 1.5 × 1012 p+/cm2 with no discernable reduction in the observed lifetime, which implies that the lifetime damage factor slope to 63 MeV proton irradiation is not greater than 2 × 10−5 cm2/s. Steady-state photoluminescence is used to evaluate the total luminescence output as a function of excitation, yielding a 2/3 power law slope consistent with Auger-limited recombination. The observed Auger-limited behavior is consistent with reports of high p-type background carrier concentration in these alloys. The temperature dependence of the steady-state photoluminescence spectra also provides the Einstein single oscillator model parameters for the ground state transition energy and Urbach energy of the GeSn quantum well.
We report the multiplication properties of Al0.85Ga0.15As0.07Sb0.93 for use in separate absorption charge and multiplication avalanche photodiode lattice matched to a GaSb substrate. The demonstration of a high gain, low excess noise multiplier lattice matched to GaSb is a critical step toward high performance avalanche photodiodes operating at wavelengths exceeding 2 μm. We have measured impact ionization coefficients of random alloy Al0.85Ga0.15As0.07Sb0.93 grown on GaSb substrates from 210 to 421 kV/cm. Our results show an α value (0.25–40×103 cm−1) significantly greater than β (0.002–4.8×103 cm−1) over the measured field range, indicating this material is a favorable multiplier candidate for electron avalanche photodiodes. We also report excess noise measurements of both p-i-n and n-i-p devices under illumination, resulting in single carrier injection. The p-i-n devices showed a low excess noise of 2.98 at a maximum gain of ∼17, while the n-i-p devices showed a high excess noise of 9.34 at a gain of ∼8, further implicating that this material predominantly multiplies electrons.
This paper presents a theoretical analysis of npBp infrared (IR) barrier avalanche photodiode (APD) performance operating at 300 K based on a quaternary compound made of AIIIBV—InGaAsSb, lattice-matched to the GaSb substrate with a p-type barrier made of a ternary compound AlGaSb. Impact ionization in the multiplication layer of InGaAsSb separate absorption, grading, charge, and multiplication avalanche photodiodes (SAGCM APDs) was studied using the Crosslight Software simulation package APSYS. The band structure of the avalanche detector and the electric field distribution for the multiplication and absorption layers were determined. The influence of the multiplication and charge layer parameters on the impact multiplication gain and the excess noise factor was analyzed. It has been shown that with the decrease in the charge layer doping level, the gain and the breakdown voltage increase, but the punch-through voltage decreases, and the linear range of the APD operating voltages widens. The multiplication layer doping level slightly affects the detector parameters, while increasing its width, the photocurrent and the breakdown voltage also increase. The detector structure proposed in this work allows us to obtain a comparable gain and lower dark currents to the APD detectors made of InGaAsSb previously presented in the literature. The performed simulations confirmed the possibility of obtaining APDs with high performance at room temperatures made of InGaAsSb for the SWIR range.