Biomass pellets are one of the most crucial feedstocks for bioenergy production on a global scale due to their numerous advantages over raw biomass resources. Pellets provide improved energy density, bulk density, moisture content, and homogeneity thereby reducing storage, handling, and transportation costs. To produce high-quality solid fuel, it is necessary to comprehend the properties of wood fuel. This study explored the potential of Khaya senegalensis (khaya) as a dedicated energy crop (DEC) for the production of green energy. It thrives in less-than-ideal conditions and grows rapidly. The low durability of energy pellets raises the risk of dust and fire during handling and storage. In addition, the potential for fines and dust formation is strongly correlated with the mechanical strength of materials. Due to this necessity, the current study examines the effects of pelletization factors, including temperature and pressure, on pellet properties, particularly on its mechanical properties. The durability and compressive strength of pellets were determined using a sieve shaker and a universal testing machine, respectively. The highest mechanical durability was observed at 3 tons of pressure and 75 degrees Celsius, each with a value of 99.6%. The maximum axial compressive strength was measured at 57.53 MPa under 5 tons of pressure. When pelletized at 125 °C, the axial compressive strength increased by 13.8037% to 66.06 MPa compared to the strength obtained at 5 tons of pressure. Pelletizing Khaya feedstocks at 4 tons of pressure, on the other hand, produced a slightly lower diametral compressive strength of 7.08 MPa compared to 7.59 MPa at 125 °C. The experimental results revealed that the aforementioned factors significantly affect the mechanical properties of pellets. The elucidation of wood biomass, solid fuel qualities and pelletization parameters of this potential energy crop may facilitate the production of high-quality pellets from Khaya senegalensis wood to meet the increasing local and worldwide energy demands.

The study describes the production of an upgrading bio oil from pyrolysis of torrefied demineralized palm empty fruit bunch (TDEFB) using a fixed bed reactor system. TDEFB used as a feedstock was produced by demineralization and torrefaction pre-treatment empty fruit bunches (EFB) on raw EFB. The pyrolysis process was examined with multiple responses such as bio oil (response, Y1), bio char (response, Y2) and bio gas (response, Y3). The effect of these pyrolysis process parameters was observed by the production of bio oil, bio char and bio gas yields as the responses. Twenty runs of pyrolysis experiments were suggested by CCD indicated the optimum pyrolysis condition were found to be at reaction temperature of 490 °C, heating rate of 85 °C/min and holding time of 250 s. The maximum bio oil yield was obtained as 51.53 % with 28.5 % of bio char and 11.97 % of bio gas under optimum condition. The p-value 0.9 which indicated that there was a good correlation between the dependable and non-dependable parameters.

This work aimed to conduct a kinetic study of cotton stalks (CSs) through TGA to examine the impact of reaction conditions on bio-oil yield derived from CS slow pyrolysis using a tube furnace lab-scale reactor, as well as a characterization of bio-oil and biochar products. The iso-conversional approaches of Kissinger–Akahira–Sunose (KAS) and Flynn–Wall–Ozawa (FWO) were applied to estimate kinetic parameter activation energy (E_a) for the range of conversion degrees (α = 0.1–0.9). The kinetic results demonstrated that the average values of E_a for secondary pyrolysis were lower compared to those of primary pyrolysis; this could be explained by the fact that mainly cellulose degrades during primary pyrolysis, which requires more energy to be degraded. The pyrolysis findings indicated that the highest yield of bio-oil was 38.5%, which occurred at conditions of 500 °C and 0.5–1 mm size, while retention time showed an insignificant effect on pyrolysis oil. GC–MS analysis demonstrated that bio-oil is dominated by phenol compounds, which account for more than 40% of its components. SEM and XRD analyses emphasized that biochar is porous and has an amorphous shape, respectively. It can be concluded that these outcomes confirm that CSs have the potential to be a good candidate for a feedstock material for bioenergy production via the pyrolysis process.

The non-isothermal thermogravimetric non-catalytic and catalytic empty fruit bunch (EFB) pyrolysis with alumina were performed at different heating rates of 10, 15, 20, 25, 30 and 40 K/min under nitrogen atmosphere at a flow rate of 100 ml/min under dynamic conditions from 301 K to 1273 K. The activation energy were calculated based on Kissinger and Ozawa methods. Both reactions followed first order reactions. By Kissinger method, the activation energy and Ln A values for non-catalytic and catalytic EFB pyrolysis with alumina were 188.69 kJ mol^-1 and 201.67 kJ/mol respectively. By Ozawa method, the activation energy values for non-catalytic and catalytic EFB pyrolysis with alumina were 189.13 kJ/mol and 201.44 kJ/mol respectively. The presence of catalyst increased the activation energy values for EFB pyrolysis as calculated by Kissinger and Ozawa methods.

Biomass lignin can be used to produce vanillin through an oxidation process. Although its purity is high, the processing time and separation efficiency are not ideal. This research aims to produce vanillin directly from Kenaf stalks without separating the lignin first from the lignocellulosic biomass. This method is greener because it does not require the separation of cellulose and hemicellulose from the biomass, thus minimizing the use of acid and alkaline solutions and saving time. A high oxygen storage capacity and release capacity of ceria as an oxidation catalyst contribute to the reversable redox properties between Ce⁴⁺ and Ce³⁺ in ceria lattice. Cerium oxide nanostructures were synthesized using a hydrothermal method treated under alkaline NaOH, followed by drying at 120 °C for 16 h and calcining at different temperatures between 400 and 600 °C for the direct oxidation of Kenaf stalks to vanillin under microwave irradiation. The catalysts were characterized for their physicochemical properties using XRD, N₂ adsorption–desorption isotherms and TEM. All synthesized CeO₂ nanostructures showed the presence of diffraction peaks assigned to the presence of cubic fluorite. The N₂ adsorption–desorption isotherms showed that all catalysts possess a Type IV isotherm, indicating a mesoporous structure. The TEM image shows the uniform shape of the CeO₂ nanostructures, while HRTEM images show that the CeO₂ nanostructures are single-crystalline in nature. All catalysts were tested for the direct oxidation of Kenaf stalks using H₂O₂ as the oxidizing agent in temperatures ranging from 160 to 180 °C for 10–30 min with 0.1–0.3 g catalyst loading under 100–500 W of microwave irradiation. The CeO₂-Nps-400 catalyst produced the highest vanillin yields of 3.84% and 4.32% for the direct oxidation of Kenaf stalks and extraction of lignin from Kenaf stalks, respectively. Compared to our earlier study, the highest vanillin yields of 2.90% and 3.70% for direct biomass and extracted lignin were achieved using a Ce/MgO catalyst.

Fuel pellets are an attractive renewable energy source derived from biomass sources thanks to their uniformity and ease of handling. However, raw biomass and waste material binders have several drawbacks, which include poor physical properties, particularly low density and compositional heterogeneity, which restrict their wider use as a general source of energy. Besides, due to the low energy density, low bulk density, and uneven shape and size of raw biomass, it is very difficult to store and transport biomass in its original form, which decreases transport efficiency. This study investigated the effect of waste material binders (rice husk, corn cob, and sugarcane bagasse) on the mechanical and thermal properties of Khaya Senagalensis pellets. The mechanical and thermal properties were determined according to ASTM standards. Waste material binders have affected pellet quality such as density, bulk density, moisture content, durability, compressive strength, shatter index, water resistance, ash content, volatile matter, fixed carbon, and calorific value. From the analysis, sugarcane bagasse as a binder shows the highest quality pellet in terms of mechanical properties. Sugarcane bagasse produces the highest density (0.967g/cm3), bulk density (0.4094), durability (99.71%), shatter index (98.85%), water resistance (98.35%), and thermal properties, which are the highest volatile matter (94.71%) and the lowest ash content (1.71%). In a nutshell, sugarcane bagasse is a good binder that gives a positive impact to the K.senegalensis pellets in terms of storage and transportation compared to corn cob and rice husk binder.