Bortecene Yildirim

Dr. Bortecene Yildirim

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 December 2022 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
BYBortecene Yildirim
Bortecene Yildirim
Mohammed ElgendyMohammed Elgendy
Mohammed Elgendy
ASAndrew Smith
Andrew Smith
VPVolker Pickert
Volker Pickert
Modular battery energy storage systems (MBESSs) enable the use of lower-rated voltage converters and battery modules, and simpler battery management systems. They also improve the system's reliability and allow flexible power sharing among different modules. This article proposes a power-sharing algorithm that maximizes the energy conversion efficiency of this battery energy storage system, considering state of charge (SoC) balancing and battery lifespan. Real-time optimum power sharing is undertaken based on a simple lookup table, whose data were generated via offline genetic algorithm optimization considering the converter's efficiency map. To demonstrate the effectiveness of the proposed algorithm, a six-module prototype system was constructed, each comprising a half-bridge converter and a 10 Ah, 12.8 V, LiFePo4 battery. System testing occurred at different battery power levels in both charging and discharging modes, using the proposed efficiency-optimized power-sharing and the conventional SoC-based power-sharing methods. The results obtained show that the proposed power-sharing control significantly improves the light load efficiency compared to the conventional and equal power-sharing methods. At high loads, the proposed method gives a higher efficiency than the SoC-based method and an equivalent efficiency to the equal power-sharing method.

15 June 2025 in Energies
Verified
Journal Article
Open access
PDF file
BYBortecene Yildirim
Bortecene Yildirim
MEMohmmed Ali Mohammed Elgendy
Mohmmed Ali Mohammed Elgendy
ASAndrew Smith
Andrew Smith
Mehmet KulanMehmet Kulan
Mehmet Kulan
BABAHADIR AKBAL
BAHADIR AKBAL
Modular converters offer an effective solution for battery energy storage systems (BESSs) by lowering battery pack voltage levels and enabling additional functionalities, such as state of charge (SoC) and state of health (SoH) balancing, temperature regulation, and improved system reliability. However, conventional modular designs often require numerous additional components, including passive elements, switches, and sensing circuits. This paper proposes a modular multi-port converter (MMPC) BESS that combines energy conversion and battery management functions, leveraging the benefits of both modular and multi-port architectures. The proposed system demonstrates promising scalability and adaptability within the tested voltage and power ranges, with potential for extension to higher voltage and power applications through modular expansion. It also introduces an additional control layer, enhancing flexibility for control optimization and cost-effectiveness while improving reliability by reducing dependency on bypass switches. A prototype utilizing three dual-port converters managing six battery packs was developed. The experimental results confirm that the MMPC-based BESS achieves energy conversion and effectively balances the SoC among battery packs during both charging and discharging, under initial SoC mismatches.

28 November 2025 in Energies
Verified
Journal Article
Open access
PDF file
Mehmet KulanMehmet Kulan
Mehmet Kulan
FMFarshid Mahmouditabar
Farshid Mahmouditabar
AAAbdulrahman Ali M ALHARBI
Abdulrahman Ali M ALHARBI
BYBortecene Yildirim
Bortecene Yildirim
Nick BakerNick Baker
Nick Baker
This paper presents the design, optimization, and validation of a dual three-phase yokeless and segmented armature (YASA) axial flux permanent magnet (AFPM) machine for aerospace actuators. The proposed 12-slot, 10-pole topology employs segmented soft magnetic composite (SMC) stator teeth integrated into an additively manufactured aluminium holder, combining modularity, weight reduction, and improved thermal conduction. A multi-objective optimization process based on 3D finite element analysis (FEA) was applied to balance torque capability and losses. The manufacturable design achieved a peak torque of 28.3 Nm at 1400 rpm and a peak output power of 3.5 kW with an efficiency of 81.6%, while limiting short-circuit currents to 14 Arms. Transient structural simulations revealed that three-phase short circuits induce unbalanced axial forces, exciting rotor wobbling—a phenomenon not previously reported for YASA machines. A prototype was fabricated and tested, with static torque measurements deviating by 8.6% from FEA predictions. By contrast, line-to-line back-EMF and generator-mode power output exhibited larger discrepancies (up to 20%), attributed to the frequency-dependent permeability and localized eddy currents of the SMC stator material introduced during EDM machining. These results demonstrate both the feasibility and the limitations of YASA AFPM machines for aerospace applications.

2 November 2026 in Electricity
Verified
Journal Article
Open access
PDF file
BYBortecene Yildirim
Bortecene Yildirim
BABAHADIR AKBAL
BAHADIR AKBAL
The increasing power levels of electric vehicle (EV) charging infrastructure, from conventional direct current (DC) fast charging to extreme-fast charging (XFC), ultra-fast charging (UFC), and emerging megawatt-class systems, are creating increasingly concentrated electrical demand at the grid interface. This paper reviews the grid interaction of high-power DC charging infrastructure by linking charging-power progression with the resulting grid impacts, the factors governing their severity, and corresponding mitigation strategies. The principal impacts include peak demand, voltage deviations and fluctuations, harmonic distortion, voltage and current unbalance, transformer and feeder loading, network losses, reactive-power requirements, and system-level stability and reliability. The synthesis shows that rated charging power alone does not characterize grid exposure; actual impacts also depend on charger utilization and simultaneity, vehicle charging characteristics, grid strength and available network capacity, and spatiotemporal charging patterns. Mitigation strategies include power electronic converter (PEC) control, battery energy storage system (BESS) and renewable energy source (RES) integration, DC microgrids, coordinated charging, vehicle-to-grid/vehicle-to-everything (V2G/V2X) operation, and grid-aware planning and reinforcement. Key research needs include realistic charging-demand representation, assessment across different grid-strength conditions, field validation of XFC/UFC and MW-class installations, multi-timescale analysis, and coordinated evaluation of mitigation strategies.

1 September 2026 in Energies
Verified
Journal Article
Open access
PDF file
BYBortecene Yildirim
Bortecene Yildirim
Mehmet KulanMehmet Kulan
Mehmet Kulan
MDMohamed Dahidah
Mohamed Dahidah
AMAmirhossein Malekipour
Amirhossein Malekipour
MMMichael Merlin
Michael Merlin
This paper presents the design and multi-objective optimization of a six-limb magnetically integrated hybrid distribution transformer (HDT). The increasing demand for efficient and compact transformer solutions in modern distribution networks motivates the development of improved design methodologies. In this work, a detailed design procedure is established, including core geometry definition, winding configuration, and magnetic circuit considerations. A multi-objective optimization framework is formulated to minimize total transformer mass and power losses while satisfying operational constraints such as magnetic flux density and current density limits in the windings. Key design parameters, including core dimensions and winding configurations, are systematically varied to identify an optimal trade-off between material usage and performance. The optimization results show a noticeable reduction in total mass with a slight improvement in total losses, while all design constraints are maintained within acceptable limits. A laboratory-scale prototype was constructed to demonstrate the proposed magnetic configuration, and experimental validation was performed under steady-state, open-loop operating conditions to verify the voltage injection principle through the integrated control and extension windings. The presented approach offers a structured pathway for the design and optimization of HDT and can serve as a basis for further studies involving advanced control and operational strategies.