Focusing on PM6 as the electron-donating polymer and the non-fullerene acceptors Y12 and PY-IT, this study investigates their chemical, optical, and morphological properties, as well as their compatibility in bulk heterojunction (BHJ) architectures. All materials were characterized in thin-film form using Fourier transform infrared (FTIR), and Raman spectroscopy. Binary blends of PM6:Y12 and PM6:PY-IT, along with the ternary PM6:PY-IT:Y12 system, were dissolved in o-xylene and processed into active layers by blade coating under ambient conditions. Optical properties were analyzed in solution and in thin films, providing insights into light-absorption efficiency and spectral complementarity. Nanoscale morphology and molecular packing were examined using atomic force microscopy (AFM) and grazing-incidence wide-angle X-ray scattering (GIWAXS), revealing correlations between material organization and device performance. The results highlight the importance of optimizing material selection, ink formulation, and film morphology to maximize charge-generation efficiency. Power-conversion efficiencies (PCEs) of 13.95%, 12.04%, and 12.17% were achieved for PM6:Y12, PM6:PY-IT, and PM6:PY-IT:Y12 devices, respectively. The ternary PM6:PY-IT:Y12 system demonstrated performance comparable to PM6:PY-IT, with improved miscibility and nearly aggregate-free morphologies, suggesting potential for further efficiency gains. These findings offer valuable guidance for designing high-performance, sustainable active layers, contributing to the development of next-generation organic photovoltaic technologies.
Ternary organic solar cells contain a single three-component photoactive layer with a wide absorption window, achieved without the need for multiple stacking. However, adding a third component into a well-known binary blend can influence the energetics, optical window, charge carrier transport, crystalline order and conversion efficiency. In the form of binary blends, the low-bandgap regioregular polymer donor poly(3-hexylthiophene-2,5-diyl), known as P3HT, is combined with the acceptor PC61BM, an inexpensive fullerene derivative. Two different non-fullerene acceptors (ITIC and eh-IDTBR) are added to this binary blend to form ternary blends. A systematic comparison between binary and ternary systems was carried out as a function of the thermal annealing temperature of organic layers (100 °C and 140 °C). The power conversion efficiency (PCE) is improved due to increased fill factor (FF) and open-circuit voltage (Voc) for thermal-annealed ternary blends at 140 °C. The transport properties of electrons and holes were investigated in binary and ternary blends following a Space-Charge-Limited Current (SCLC) protocol. A favorable balanced hole–electron mobility is obtained through the incorporation of either ITIC or eh-IDTBR. The charge transport behavior is correlated with the bulk heterojunction (BHJ) morphology deduced from atomic force microscopy (AFM), contact water angle (CWA) measurement and 2D grazing-incidence X-ray diffractometry (2D-GIXRD).
Thick-film organic photovoltaics (OPVs) are key for scalable manufacturing, but increasing active-layer thickness usually lowers power conversion efficiency (PCE) due to charge recombination and limited carrier extraction. We report high-efficiency thick-film OPVs fully processed in air by doctor blading using non-halogenated solvents (o-xylene with 3.5% tetralin) for two non-fullerene acceptor systems: PM6:ITIC-4F and PTQ-10:ITIC-4F. Active layers (100–500 nm) were fabricated by adjusting the coating speed while keeping the ink concentration and gap constant. Under mild drying (40 °C, 2 min), both systems exhibited significant efficiency losses at 1 sun (AM1.5G) as the thickness increased, whereas performance was largely preserved under indoor LED illumination (200 lx and 1000 lx), enabling high performance for thick films. Short thermal post-annealing (80–140 °C, 2 min) further improved PCE by reducing bimolecular recombination and enhancing nanostructure. Optimized PM6:ITIC-4F devices reached 10.2% (300 nm) under 1 sun and 14.78% at 200 lx; PTQ-10:ITIC-4F achieved 11.3% (500 nm) under 1 sun and up to 15.71% at 200 lx. Morphological and structural analysis indicates that the superior thick-film performance of PTQ-10:ITIC-4F is linked to favorable phase behavior, polymer-rich surface composition, and preferential face-on molecular orientation, promoting charge collection. These results demonstrate that low-cost PTQ-10 and non-halogenated air processing can enable industrially relevant, high-performance thick-film OPVs.