This study investigated the structural properties and catalytic performance of cobalt-based hybrid bifunctional catalysts incorporating mesoporous ZSM-23 zeolites for Fischer–Tropsch (FT) synthesis. The zeolite was pretreated with 0.1–0.5 M NaOH solutions to introduce mesoporosity, and the resulting catalysts were prepared by mixing the zeolite with a Co–Al/SiO2 FT catalyst and a boehmite binder. The porous structure, surface acidity, phase composition, and reducibility of the zeolite and catalyst samples were characterized by N2 adsorption–desorption, IR spectroscopy, X-ray diffraction (XRD), and hydrogen temperature-programmed reduction (H2-TPR). Alkaline treatment increased mesopore volume and Lewis acid site concentration while decreasing microporosity and Brønsted acid site concentration. Catalytic performance was evaluated in a fixed-bed reactor at 250°C, 2.0 MPa, and a gas hourly space velocity (GHSV) of 1000 h–1. The catalyst containing ZSM-23 treated with 0.25 M NaOH achieved the highest yield of C5–C18iso-alkanes (47.6 wt %). These findings demonstrate that the selectivity of hybrid FT catalysts toward valuable engine-fuel components can be selectively enhanced by tuning ZSM-23 porosity.
This study investigates a silica-gel-supported cobalt catalyst for synthesizing long-chain hydrocarbons (C19+) from CO and H2. The process conditions were varied within the following ranges: pressure, 1.5–3.5 MPa; gas hourly space velocity (GHSV), 300–830 h–1; H2/CO ratio, 2.0–2.3; and temperature, 187–213°C. Catalytic testing revealed a correlation between the catalyst deactivation rate and the content of C19+ hydrocarbons in the products. When the C19+ content increased from approximately 40 to 55 wt %, the deactivation rate increased more than tenfold. Under optimized conditions (H2/CO = 2.3, P = 2.0 MPa, T = 193°C), the C19+ content reached ~46–50 wt %, and the deactivation rate was minimized. A long-term stability test over 500 h was used to project a catalyst cycle length, which was found to be at least 4000 h. The study results provide a foundation for optimizing Fischer–Tropsch process conditions to maximize catalyst lifetime and selectivity toward heavy hydrocarbons, supporting the recommendation of the proposed catalyst for industrial implementation.
The effect of palladium addition to a hybrid Co/SiO2 + HZSM-5 + Al2O3 catalyst on the combined Fischer–Tropsch (FT) synthesis and hydrocarbon hydroconversion process was studied. Catalysts with a Pd content of 0.075–0.3 wt.% were characterized by a complex of physicochemical methods, including synchrotron radiation X-ray diffraction (SR-XRD), temperature-programmed reduction with hydrogen (H2-TPR), temperature-programmed desorption of hydrogen with oxygen titration (H2-TPD/O2 titration), IR spectroscopy of adsorbed pyridine, and STEM-EDX analysis. It was found that the addition of palladium decreases the cobalt oxide reduction temperature due to interphase hydrogen transfer. Tests in hydrocarbon synthesis at 240–250 °C, a pressure of 2 MPa, and an H2/CO ratio of 2 showed that the sample with 0.15% Pd exhibits the highest selectivity for C5+ hydrocarbons (66.8% at 240 °C) and stability for 150 h. Analysis of the synthesis products revealed a fivefold decrease in the proportion of alkenes and an increase in isoalkanes with increasing Pd concentration. This effect enables the in situ hydroprocessing of primary FT products in a single reactor. The results demonstrate that the targeted introduction of palladium into the hybrid system is an effective strategy for regulating its functionality, allowing for the one-stage production of high-quality fuels with a controlled hydrocarbon composition from syngas.
Thermal pyrolysis of polyethylene (PE) under pressure and hydroisomerization over Pt/SAPO-11 are known separately; this work examines their integration. PE was pyrolyzed at 400–550 °C and constant pressures of 0.1–2.0 MPa, and the 140–280 °C fraction (pyrolysis kerosene) was hydroisomerized over 0.5 wt% Pt/SAPO-11. The yield of the 140–280 °C fraction decreases with temperature and increases with pressure, reaching 45.3 wt% at 400 °C and 1.0 MPa (27.4 wt% at 0.1 MPa); a control run under these conditions gave a directly measured gas yield of 13.2 wt% and a mass balance closure of 99.3%. The pyrolysis kerosene contains 47.6 wt% alkenes and 20.0 wt% cycloalkanes. Hydroisomerization at 6 MPa and a liquid hourly space velocity of 3 h−1 gives 91.1–93.4 wt% of the kerosene fraction (>140 °C) at 290–300 °C, with near-complete alkene hydrogenation; at 330 °C, the freezing point falls below −90 °C (pyrolysis kerosene: −13 °C), but hydrocracking reduces the yield to 72.4 wt%. The kerosene fraction obtained at the selected temperature of 300 °C (57.2% isoalkanes, 25.1% cycloalkanes, 0.1% aromatics) meets all measured GOST 10227-86 requirements for Russian RT jet fuel except density. The overall kerosene yield is 41.3 wt% of PE (40.0–40.4 wt% within the 140–280 °C boundaries). A preliminary estimate shows that the heat and hydrogen demand of the process corresponds to 68–97% of the energy of the pyrolysis gases.
A method was developed for the synthesis of ZSM-48 zeolite (RFE topology) under static hydrothermal conditions without the use of hydroxide ions. The absence of an alkaline component eliminates the ion-exchange step. The use of boehmite or aluminum isopropoxide in the absence of seed crystals was shown to result in the formation of the TON topology (ZSM-22), whereas the use of seed crystals provides a highly crystalline RFE-type phase. The Si/Al molar ratio was varied from ∞ to 100 to control the acid properties of the zeolites. An increase in the aluminum content was found to increase the concentration of acid sites from 24 to 171 μmol NH3/g while maintaining a well-developed porous structure (SBET = 130 m2/g). A Pt-containing bifunctional Pt/Z48/Al2O3 catalyst was prepared using Z48-6 zeolite with optimal textural and acid properties. The catalyst was studied in hydroisodeparaffinization of a diesel fraction obtained by Fischer–Tropsch synthesis from synthesis gas with H2/CO = 2.04 and a CO + H2 content of 85.7 vol %. Under optimal conditions (4.0 MPa, 330°C, 3 h–1), the cold filter plugging point of the hydroisodeparaffinization product was –49°C, the cloud point was –42°C, and the closed-cup flash point was +57°C, which meets the requirements of GOST R 55475-2013 for DT-A-48 Arctic diesel fuel.