High alumina cement was used widely in the UK after World War I, expressing its higher content of aluminum oxide in comparison to Portland cement. Several descriptions of investigations on calcium aluminate cements appeared, starting around 1850, with a first patent field in 1888 (Scrivener and Capmas, in Hewlett 1998). More widely known is the work of Bied (1909, 1926) filing a patent in 1909 for the fabrication of cement using bauxite or some similar aluminum or iron-rich material, with low SiO2-contents and limestone. In 1918, the trade name Ciment Lafarge Fondue was used for the...
The reaction of wollastonite (CaSiO3) with CO2 in the presence of aqueous solutions (H2O) and varied temperature conditions (296 K, 323 K, and 333 K) was investigated. The educts (CaSiO3) and the products (CaCO3 and SiO2) were analyzed by scanning electron microscopy (SEM), powder X-ray diffraction (PXRD), and differential scanning calorimetry with thermogravimetry coupled with a mass spectrometer and infrared spectrometer (DSC TG/MS/IR). The reaction rate increased significantly at higher temperatures and seemed less dependent on applied pressure. It could be shown that under the defined conditions wollastonite can be applied as a cementitious material for sealing wells considering CCS applications, because after 24 h the degree of conversion from CaSiO3 to CaCO3 at 333 K was very high (>90%). As anticipated, the most likely application of wollastonite as a cementitious material in CCS would be for sealing the well after injection of CO2 in the reservoir.
Lithium plays an increasing role in battery applications, but is also used in ceramics and other chemical applications. Therefore, a higher demand can be expected for the coming years. Lithium occurs in nature mainly in different mineralizations but also in large salt lakes in dry areas. As lithium cannot normally be analyzed using XRF-techniques (XRF = X-ray Fluorescence), the element must be analyzed by time consuming wet chemical treatment techniques. This paper concentrates on XRD techniques for the quantitative analysis of lithium minerals and the resulting recalculation using additional statistical methods of the lithium contents. Many lithium containing ores and concentrates are rather simple in mineralogical composition and are often based on binary mineral assemblages. Using these compositions in binary and ternary mixtures of lithium minerals, such as spodumene, amblygonite, lepidolite, zinnwaldite, petalite and triphylite, a quantification of mineral content can be made. The recalculation of lithium content from quantitative mineralogical analysis leads to a fast and reliable lithium determination in the ores and concentrates. The techniques used for the characterization were quantitative mineralogy by the Rietveld method for determining the quantitative mineral compositions and statistical calculations using additional methods such as partial least square regression (PLSR) and cluster analysis methods to predict additional parameters, like quality, of the samples. The statistical calculations and calibration techniques makes it especially possible to quantify reliable and fast. Samples and concentrates from different lithium deposits and occurrences around the world were used for these investigations. Using the proposed XRD method, detection limits of less than 1% of mineral and, therefore down to 0.1% lithium oxide, can be reached. Case studies from a hard rock lithium deposit will demonstrate the value of mineralogical monitoring during mining and the different processing steps. Additional, more complex considerations for the analysis of lithium samples from salt lake brines are included and will be discussed.
Bauxite deposits in the Amazon region are commonly covered by yellowish clays which can reach up to 25m thick, known as Belterra Clay (BTC). In Rondon do Pará, Eastern Amazon, BTC is 13m thick and covers world-class bauxite reserves. Three pilot bauxite mines were investigated in Rondon do Pará for an initial characterization of the local BTC. In discordant contact with the lateritic profile, the BTC has reddish brown colors at its base to ocher tones towards the top. It has a massive structure with silt-clayey texture and nodular bauxitic fragments at its base. Rietveld mineral quantification of the material attests that it is dominated by kaolinite, with goethite, gibbsite, hematite, anatase and residual quartz. The thermal behavior of the material also confirms its mineralogical composition. Kaolinite is of low structural order, which was considered the main difficulty in the application of the Rietveld method. Goethite has up to 33 mol% of Al. As observed by scanning electron microscopy (SEM), the minerals represent pseudo-hexagonal crystals measuring from 150 to 700 nm. The BTC in the studied area is correlated to BTC on others bauxitic deposits of the Amazon region, suggesting this material experienced the same genesis and geological evolution, probably during the Pliocene.
Mineralogical appraisal is an important tool for both mining and industrial processes. X-ray powder diffraction analysis (XRPD) can deliver fast and reliable mineralogical quantification results to aid industrial processes and improve ore recoveries. Furthermore, X-ray fluorescence (XRF) chemical data, thermal analysis (TA), and Fourier-transformed infrared spectroscopy (FTIR) can be used to validate and refine XRPD results. Mineralogical assessment of non-traditional ores, such as mining wastes, is also an important step to consider them for near-future industries. In the Brazilian Amazon, alumina-rich clays cover the largest and most important bauxitic deposits of the region and have been considered as a possible raw material for the local cement and ceramic industry. In this work, a mineralogical evaluation of these clays (Belterra Clays) is performed using XRPD, XRF, TA, and FTIR. XRPD-Rietveld quantification confirmed that kaolinite is the main phase of the clay overburden, followed by variable contents of gibbsite and goethite and minor quantities of hematite, anatase, and quartz. The chemistry derived from Rietveld, based on stoichiometric phase compositions, presents a good correlation with the XRF data and is also supported by the TA and FTIR data. The initially assumed homogeneous composition of Belterra Clay is revealed to be variable by the present mineralogical study.