Stefan Björklund

Stefan Björklund


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 July 2015 in Coatings
Verified
Journal Article
Open access
PDF file
NCNicholas Curry
Nicholas Curry
KVKent Vanevery
Kent Vanevery
TSTodd Snyder
Todd Snyder
JSJohann Susnjar
Johann Susnjar
SBStefan Björklund
Stefan Björklund
Suspension plasma spraying has become an emerging technology for the production of thermal barrier coatings for the gas turbine industry. Presently, though commercial systems for coating production are available, coatings remain in the development stage. Suitable suspension parameters for coating production remain an outstanding question and the influence of suspension properties on the final coatings is not well known. For this study, a number of suspensions were produced with varied solid loadings, powder size distributions and solvents. Suspensions were sprayed onto superalloy substrates coated with high velocity air fuel (HVAF) -sprayed bond coats. Plasma spray parameters were selected to generate columnar structures based on previous experiments and were maintained at constant to discover the influence of the suspension behavior on coating microstructures. Testing of the produced thermal barrier coating (TBC) systems has included thermal cyclic fatigue testing and thermal conductivity analysis. Pore size distribution has been characterized by mercury infiltration porosimetry. Results show a strong influence of suspension viscosity and surface tension on the microstructure of the produced coatings.

23 July 2021 in Coatings
Verified
Journal Article
Open access
PDF file
MMMonika Michalak
Monika Michalak
Pawel SokolowskiPawel Sokolowski
Pawel Sokolowski
Mirosław SzalaMirosław Szala
Mirosław Szala
Mariusz WalczakMariusz Walczak
Mariusz Walczak
Leszek ŁatkaLeszek Łatka
Leszek Łatka
SBStefan Björklund
Stefan Björklund
Thermally sprayed ceramic coatings are applied for the protection of surfaces that are exposed mainly to wear, high temperatures, and corrosion. In recent years, great interest has been garnered by spray processes with submicrometric and nanometric feedstock materials, due to the refinement of the structure and improved coating properties. This paper compares the microstructure and tribological properties of alumina coatings sprayed using conventional atmospheric plasma spraying (APS), and various methods that use finely grained suspension feedstocks, namely, suspension plasma spraying (SPS) and suspension high-velocity oxy-fuel spraying (S-HVOF). Furthermore, the suspension plasma-sprayed Al2O3 coatings have been deposited with radial (SPS) and axial (A-SPS) feedstock injection. The results showed that all suspension-based coatings demonstrated much better wear resistance than the powder-sprayed ones. S-HVOF and axial suspension plasma spraying (A-SPS) allowed for the deposition of the most dense and homogeneous coatings. Dense-structured coatings with low porosity (4 vol.%) and good cohesion to the metallic substrate, containing a high content of α–Al2O3 phase (56 vol.%) and a very low wear rate (0.2 ± 0.04 mm3 × 10−6/(N∙m)), were produced with the S-HVOF method. The wear mechanism of ceramic coatings included the adhesive wear mode supported by the fatigue-induced material delamination. Moreover, the presence of wear debris and tribofilm was confirmed. Finally, the coefficient of friction for the coatings was in the range between 0.44 and 0.68, with the highest values being recorded for APS sprayed coatings.

11 July 2019 in Materials
Verified
Journal Article
Open access
PDF file
SMSatyapal Mahade
Satyapal Mahade
NCNicholas Curry
Nicholas Curry
SBStefan Björklund
Stefan Björklund
NMNicolaie Markocsan
Nicolaie Markocsan
Shrikant JoshiShrikant Joshi
Shrikant Joshi
Higher durability in thermal barrier coatings (TBCs) is constantly sought to enhance the service life of gas turbine engine components such as blades and vanes. In this study, three double layered gadolinium zirconate (GZ)-on-yttria stabilized zirconia (YSZ) TBC variants with varying individual layer thickness but identical total thickness produced by suspension plasma spray (SPS) process were evaluated. The objective was to investigate the role of YSZ layer thickness on the durability of GZ/YSZ double-layered TBCs under different thermal cyclic test conditions i.e., thermal cyclic fatigue (TCF) at 1100 °C and a burner rig test (BRT) at a surface temperature of 1400 °C, respectively. Microstructural characterization was performed using SEM (Scanning Electron Microscopy) and porosity content was measured using image analysis technique. Results reveal that the durability of double-layered TBCs decreased with YSZ thickness under both TCF and BRT test conditions. The TBCs were analyzed by SEM to investigate microstructural evolution as well as failure modes during TCF and BRT test conditions. It was observed that the failure modes varied with test conditions, with all the three double-layered TBC variants showing failure in the TGO (thermally grown oxide) during the TCF test and in the ceramic GZ top coat close to the GZ/YSZ interface during BRT. Furthermore, porosity analysis of the as-sprayed and TCF failed TBCs revealed differences in sintering behavior for GZ and YSZ. The findings from this work provide new insights into the mechanisms responsible for failure of SPS processed double-layered TBCs under different thermal cyclic test conditions.

24 July 2019 in Materials
Verified
Journal Article
Open access
PDF file
SMSatyapal Mahade
Satyapal Mahade
KGKarthik Narayanan Giriprasad
Karthik Narayanan Giriprasad
SGSivakumar Govindarajan
Sivakumar Govindarajan
SBStefan Björklund
Stefan Björklund
NCNicholas Curry
Nicholas Curry
Shrikant JoshiShrikant Joshi
Shrikant Joshi
Titanium- and chromium-based carbides are attractive coating materials to impart wear resistance. Suspension plasma spraying (SPS) is a relatively new thermal spray process which has shown a facile ability to use sub-micron and nano-sized feedstock to deposit high-performance coatings. The specific novelty of this work lies in the processing of fine-sized titanium and chromium carbides (TiC and Cr3C2) in the form of aqueous suspensions to fabricate wear-resistant coatings by SPS. The resulting coatings were characterized by surface morphology, microstructure, phase constitution, and micro-hardness. The abrasive, erosive, and sliding wear performance of the SPS-processed TiC and Cr3C2 coatings was also evaluated. The results amply demonstrate that SPS is a promising route to manufacture superior wear-resistant carbide-based coatings with minimal in situ oxidation during their processing.

15 May 2024 in Coatings
Verified
Journal Article
Open access
PDF file
MBMadhura Bellippady
Madhura Bellippady
SBStefan Björklund
Stefan Björklund
XLXin-Hai Li
Xin-Hai Li
RFRobert Frykholm
Robert Frykholm
BKBjorn Kjellman
Bjorn Kjellman
NMNicolaie Markocsan
Nicolaie Markocsan
This work represents a preliminary study of atmospheric plasma-sprayed (APS) Yttria-Stabilized Zirconia (YSZ)-based thermal barrier coatings (TBCs) deposited on forged and additive manufactured (AM) HAYNES®282® (H282) superalloy substrates. The effect of different feedstock morphologies and spray gun designs with radial and axial injection on APS-deposited YSZ layer characteristics such as microstructure, porosity content, roughness, etc., has been investigated. The performance of TBCs in terms of thermal cycling fatigue (TCF) lifetime and erosion behaviour were also comprehensively investigated. In view of the high surface roughness of as-built AM surfaces compared to forged substrates, two different types of NiCoCrAlY bond coats were examined: one involved high-velocity air fuel (HVAF) spraying of a finer powder, and the other involved APS deposition of a coarser feedstock. Despite the process and feedstock differences, the above two routes yielded comparable bond coat surface roughness on both types of substrates. Variation in porosity level in the APS topcoat was observed when deposited using different YSZ feedstock powders employing axial or radial injection. However, the resultant TBCs on AM-derived substrates were observed to possess similar microstructures and functional properties as TBCs deposited on reference (forged) substrates for any given YSZ deposition process and feedstock.

5 March 2019 in Coatings
Verified
Journal Article
Open access
PDF file
ASHISH GANVIRASHISH GANVIR
ASHISH GANVIR
SBStefan Björklund
Stefan Björklund
YYYiming Yao
Yiming Yao
SVSrikanth Vadali
Srikanth Vadali
UKUta Klement
Uta Klement
SJShrikant Joshi
Shrikant Joshi
This paper demonstrates, for the first time ever, the deposition of graphenaceous composite coatings using an easy, yet robust, suspension plasma spraying (SPS) process. As a case study, a composite coating comprising 8 wt.% of yttria-stabilized-zirconia (8YSZ) and reinforced with graphene oxide (GO) was deposited on a steel substrate. The coatings were sprayed using an 8YSZ-GO mixed suspension with varied plasma spray parameters. Establishing the possibility of retaining the graphene in a ceramic matrix using SPS was of specific interest. Electron microscopy and Raman spectroscopy confirmed the presence of graphenaceous material distributed throughout the coating in the 8YSZ matrix. The experimental results discussed in this work confirm that SPS is an immensely attractive pathway to incorporate a graphenaceous material into virtually any matrix material and can potentially have major implications in enabling the deposition of large-area graphene-containing coatings for diverse functional applications.