The aim of the article is to demonstrate the impact of the type of pumped oil on the values of kinematic excitations. Three groups of oils were examined: engine oils, hydraulic oils, and gear oils. The research methodology focused on measuring the average kinematic excitation and the dynamics of...
1 February 2020 in IOP Conference Series: Materials Science and Engineering
Compressed air is a very widely used energy medium, used in various fields. Is one of the most widespread, but also one of the most expensive working media used in modern industry. According to studies available in the literature in Australia and the European Union, energy consumption by compressed air systems accounts for about 10% of total industrial energy consumption, while in the United States it accounts for 30% of total electricity consumption. In addition, these systems are one of the least efficient forms of energy - only about 10-30% of the energy generated by the compressor reaches the end point. This is primarily due to a change in the form of energy (e.g. heat), but also leaks in the network and inefficient use. During operation in the compressed air network, pressure losses (linear and local) occur as a result of pipeline construction as well as pressure losses caused by the use of devices and elements responsible for maintaining adequate air quality (local losses) in the network. The pressure drop caused by the pipeline elements will depend on the extent of the network, the diameter of the pipeline, the number of places where there is a change in the direction of air flow (elbows, venturi, etc.). However, the losses caused by the use of treatment elements will depend on the expected air quality (number of filtration stages, appropriate air dryer) as well as on the network operation time (e.g. air filter contamination). The purpose of this study is to determine the impact of compressed air network extensions on energy losses resulting from, among others friction during flow. The values of these losses depend on many parameters such as efficiency, air flow speed, diameter and length of the pipeline. Knowledge about the correlation of these parameters will allow for proper selection of compression devices, as well as for optimal design of the pneumatic network.
The aim of the research was to evaluate the influence of the initial roughness of a steel pin cooperating with a graphite ring—dry and wet—on the mechanism of sliding layer formation. A ring–pin friction pair was used for the study, where the rings were made of expanded graphite, while the pins were made of acid-resistant steel. In the first case, the steel pin interacted with a dry graphite ring, and in the second case, the graphite rings were moist. To determine the effect of initial surface roughness, the pins were divided into three roughness groups. To determine changes in surface geometry due to material transfer, the Ra and Rz parameters were measured. This project investigated how the initial roughness value of the steel surface pin cooperating with expanded graphite influences the formation of the sliding layer. Increasing the initial roughness of the steel surface interacting with the graphite contributes to faster layer formation and reduced roughness. The state of the expanded graphite—dry and wet—influences the formation of the sliding layer of graphite—a wet graphite component causes a faster smoothing of the steel surface. The running time of the wear apparatus has an effect on the resulting layer. The highest roughness group is the most favorable from the viewpoint of sliding layer formation.
The sliding layer created during operation of the expanded graphite–steel combination has had a huge impact on the effectiveness of the friction process, and thus on the sustainable development of society. Knowledge of the factors determining the properties of the sliding layer will make it possible to reduce friction resistance in the future through the proper design and selection of sliding pairs for given applications. This paper studies the effect of the moisture content of expanded graphite on the formation of a sliding layer on a stainless steel surface. The tests were carried out in static contact for 30 s and dynamic contact for 15 and 30 min, for loads of 10, 20, and 30 N and speeds of 25 and 50 mm/s. To determine the changes in surface geometry due to material transfer, the Ra roughness value of the surface of stainless steel samples was measured. In order to realize the purpose of the work and evaluate the effect of moist rings on the resulting sliding layer, the results of the surface roughness of stainless steel samples working with dry and moist graphite rings were compiled. The obtained results show that the presence of water in the stainless steel-expanded graphite friction node affects the formation of a sliding layer. The resulting layer reduces the surface roughness of the cooperating materials and prevents their accelerated wear. After 5 min of work with the water-soaked graphite counter-sample, depending on the applied friction conditions, a reduction in the surface roughness of the stainless steel sample was achieved in the range of 11–18% compared to the initial value. After 30 min of operation, the surface roughness decreased by 3 to 25%. Pilot studies have shown that operating conditions influence the formation of a sliding layer in the stainless steel-expanded graphite tribological contact. This confirms the validity of conducting further research in this area.
Low-temperature contact freezing refrigeration solutions available on the market typically contain refrigerants inside the plates, which may result in harmful emissions into the atmosphere and the contamination of food products in case of failure. However, a concept for a refrigeration plant with new coolant—a solution of potassium formate—is introduced in this paper. It comprises two systems: the primary one, where the compressor system is cooling down the coolant in the evaporator (as a heat and mass exchanger), and the secondary one, where the pump system is responsible for coolant circulation. As a coolant in the intermediate system, a 48% aqueous solution of potassium formate was utilized due to its numerous benefits. This liquid is neutral to the pump circuit installation materials and does not pose a threat to the food product in case of leakage, as it is also used as a food preservative additive. The use of liquid coolant ensures that any malfunction results in a visible leak, allowing for prompt intervention, unlike refrigerants that escape unnoticed into the atmosphere. Moreover, a refrigerant with a lower GWP than traditional solutions was chosen, making the system more eco-friendly.
Wydawnictwo SIGMA-NOT wydaje czasopisma fachowe informuj?ce swoich czytelnik?w o najnowszych osi?gni?ciach naukowych i nowoczesnych rozwi?zaniach technicznych w Polsce i na ?wiecie, popularyzuje problemy techniczne oraz poszerza wiedz? i kultur? techniczn?.