bin Jia

Prof. Dr. bin Jia


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2008 in Transactions of Tianjin University
Verified
Journal Article
Closed access
PDF file
BJbin Jia
bin Jia
JTJunlin Tao
Junlin Tao
ZLZhengliang Li
Zhengliang Li
RWRuheng Wang
Ruheng Wang
YZYu Zhang
Yu Zhang

16 November 2022 in Buildings
Verified
Journal Article
Open access
PDF file
Rui GUORui GUO
Rui GUO
DYDan Yang
Dan Yang
BJbin Jia
bin Jia
DTDeyun Tang
Deyun Tang
A total of nine specimens were constructed and tested under cyclic loads to investigate the differences in seismic behavior between glass fiber-reinforced polymer (GFRP)-reinforced concrete (RC) joints and RC beam-to-column joints. The experimental parameters included stirrup ratios, axial pressure ratios and concrete strength of the beam-to-column joints. The cyclic loading test results showed that the GFRP-RC beam-to-column joints can withstand significantly high lateral deformations without exhibiting brittle failure. Moreover, the RC beam-to-column joint exhibited significantly higher energy dissipation and residual displacement than the GFRP-RC beam-to-column joint by 50% and 60%, respectively. Finally, a shear capacity calculation method for the core zone of this kind of joint was proposed, which agreed well with the experimental results.

3 January 2025 in Materials
Verified
Journal Article
Open access
PDF file
XHXiangyu Han
Xiangyu Han
QZQILONG Zhao
QILONG Zhao
BJbin Jia
bin Jia
JLJinqiao Liu
Jinqiao Liu
QLQionglin Li
Qionglin Li
QZQuan Zhang
Quan Zhang
Defects can be introduced into shotcrete materials after a few freeze–thaw cycles, which has a significant influence on the fracture performance of shotcrete. In this study, a series of shotcrete specimens with varying sizes, geometries, and initial crack lengths were prepared to investigate the fracture properties of notched shotcrete under freeze–thaw conditions. Considering the effects of specimen boundaries and material microstructure, a linear closed-form solution was proposed to determine the fracture toughness of frost-damaged shotcrete. The fracture toughness was found to be a reliable material constant, independent of specimen geometry variations. Results from three-point bending (3PB) tests show that freeze–thaw cycles severely weaken the fracture toughness of shotcrete, which is consistent with CT scan images of the damaged microstructure of the shotcrete specimens. Moreover, specimens with longer initial notches exhibited more severe freeze–thaw damage, which should be carefully considered in practical engineering assessments. These findings highlight the critical importance of considering freeze–thaw effects and notch length when evaluating the durability of shotcrete in cold region applications.

27 February 2024 in Heliyon
Verified
Journal Article
Open access
SJShi Jianjun
Shi Jianjun
WWWenze Wang
Wenze Wang
WWWangcheng Wei
Wangcheng Wei
BJbin Jia
bin Jia
The Carbon Fiber Reinforced Polymer (CFRP)-wrapped steel pipeline system is emerging as an alternative for the repair and long-distance transportation of oil and gas. This system is recognized as a composite material. Under internal pressure, the pipe predominantly undergoes circumferential stretching. This study derives the tensile constitutive model of the steel-CFRP composite material using uniaxial tensile tests and the rule of mixtures. Subsequently, utilizing this newly calibrated constitutive model, a computational model to assess the internal pressure capacity of the steel-carbon fiber composite pipe was established. Finally, a comparison between the theoretical outcomes of the computational model and the actual internal pressure test results revealed a high degree of correlation. This holds substantial significance for the design and practical implementation of this novel composite pipeline system.

16 October 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SYSheng Ying
Sheng Ying
ZYZhenchao Yang
Zhenchao Yang
YMYu Meng
Yu Meng
BJbin Jia
bin Jia
(1) Background: In most cases, passive isolation control methods are commonly used for the seismic isolation design in bridge engineering. However, passive seismic isolation devices, due to their non-adjustable performance parameters, struggle to achieve effective seismic isolation across a wide frequency range of 0 Hz to 20 Hz in response to random and varying seismic loads. (2) Methods: The sensitivity of the design parameters of the seismic isolation bearing was analyzed using the optimization center gradient method, and an improved genetic algorithm was employed to quickly optimize and obtain the optimal design parameters. (3) Results: The effectiveness of the three-dimensional seismic isolation bearing was validated through experiments. (4) Conclusions: The multi-factor sensitivity analysis approach used in this study for designing novel isolation bearings is applicable not only to seismic design in bridges but also serves as a reference for parameter design in isolation bearings requiring medium to high precision in seismic performance.

3 March 2026 in Materials
Verified
Journal Article
Open access
PDF file
PRPeng Ren
Peng Ren
YFYafang Fu
Yafang Fu
JHJifan He
Jifan He
NLNaixian Li
Naixian Li
LZLi Zhu
Li Zhu
BJbin Jia
bin Jia
In the field of oil and gas transportation, X80 pipelines are susceptible to localized plastic deformation caused by mechanical impact or geological activity. This leads to the formation of dents and the introduction of pre-strain, thereby affecting the structural integrity and fatigue life. This study systematically investigates the influence mechanism of pre-strain on the high-cycle fatigue performance of dented regions in X80 steel. Fatigue tests conducted across pre-strain levels of 1%, 2%, and 3% revealed that the induced plastic strain significantly degrades fatigue performance. Under constant stress amplitude, fatigue life decreases markedly with increasing pre-strain, a trend driven by the accumulation of micro-damage. Furthermore, a parametric P-S-N curve model that incorporates both pre-plastic strain and reliability was developed, providing a basis for quantitatively assessing the impact of pre-strain. By combining finite element analysis with the Smith-Watson-Topper (SWT) critical plane method, it was predicted that fatigue cracks in unconstrained dent primarily initiate at the dent periphery, with the critical plane orientation perpendicular to the circumferential direction, which aligns well with field observations. Parametric analysis indicates that the maximum operating pressure is the dominant factor affecting the fatigue life of the dented pipelines. This research elucidates the material-level fatigue failure characteristics of dented X80 pipelines and provides theoretical insights for life prediction and engineering protection.