The paper presents selected isotropic and anisotropic mathematical models to calculate the distribution of solar radiation on the photovoltaic module plane with any spatial orientation. A comparison of solar radiation models for Poland is based on measured data and received from the Institute of Meteorology and Water Management. Power density of solar radiation for different angular positions, especially for representative days of each month, was calculated. Based on the statistical analysis of the percentage root-mean-square error (RMSE%), mean-bias error (MBE%) and the Pearson correlation coefficient of an individual mathematical model, our own correction factor for diffuse radiation was proposed. A modified Liu-Jordan model was compared with six common mathematical models showing better agreement of measured and calculated values of solar radiation density. The presented analysis explains which mathematical model is the most suitable for central Poland (Poznań, 52°25’ N, 16°56’ E) and shows the validity of applying the modified model to improve the accuracy of determination of the radiation power density for a given elevation and azimuth angle using values for a horizontal plane.

This paper presents a comparison of the 24-month production of electricity and momentary power by two photovoltaic systems with a nominal power of 1000 W_p each. The analyzed systems are connected to the power grid and operate independently: a fixed system with optimal all-year-round angular positioning and an astronomical-sensor-controlled dual-axis tracking system. The systems under consideration consist of PV modules with a unit electrical power of 200 W_p, and the production technology of those modules is the same. The tested systems were located on the building rooftop of the Faculty of Control, Robotics and Electrical Engineering of the Poznan University of Technology in Poland (Central Poland, 52°24.4152′ N, 16°55.7958′ E) at a height of 30 m above ground level. The measurements take into account the consumption of electricity by the actuators of the dual-axis positioning system. Increases in the produced electricity by 35.6% and 44.7% were observed for local climatic conditions during the first and second measuring years, respectively, when comparing the use of the dual-axis tracking system with the use of fixed units. Results show that the analyzed region of central Poland, represented by the city of Poznań, creates favorable climatic conditions for the use of astronomical-sensor spatial positioning systems for photovoltaic modules, also in the case of a significant share of diffuse solar radiation in the global value. These results may make the planning of solar tracking investments easier and help with the estimate calculations of the total investment return period and operational costs.

The development and advantages of renewable energy technologies mean that their areas of application are constantly expanding. The development of roads, transport systems, and electromobility also increases the demand for electricity. Roads occupy a certain area that could be used to install wind turbines or photovoltaic systems that could be used to power, among others, electric vehicle charging stations and road technical infrastructure facilities (travel service areas, tunnel lighting, road signs). There are many examples around the world where such solutions have been used. This critical review of existing solutions and the possibilities of their application in new places may contribute to further development and research in this area. Particular attention was paid to the possibility of using renewable energy systems in Poland, which can be successfully transferred to other countries with a similar climate.

The paper presents the most representative – from the three-year measurement time period – characteristics of daily and monthly electricity production from a photovoltaic conversion using modules installed in a fixed and 2-axis tracking construction. Results are presented for selected summer, autumn, spring and winter days. Analyzed measuring stand is located on the roof of the Faculty of Electrical Engineering Poznan University of Technology building. The basic parameters of the statistical analysis like mean value, standard deviation, skewness, kurtosis, median, range, or coefficient of variation were used. It was found that the asymmetry factor can be useful in the analysis of the daily electricity production from a photovoltaic conversion. In order to determine the repeatability of monthly electricity production, occurring between the summer, and summer and winter months, a non-parametric Mann-Whitney U test was used as a statistical solution. In order to analyze the repeatability of daily peak hours, describing the largest value of the hourly electricity production, a non-parametric Kruskal-Wallis test was applied as an extension of the Mann-Whitney U test. Based on the analysis of the electric energy distribution from a prepared monitoring system it was found that traditional forecasting methods of the electricity production from a photovoltaic conversion, like multiple regression models, should not be the preferred methods of the analysis.

This paper presents the results of the computational fluid dynamics (CFD) simulation of the airflow for a 300 W horizontal axis wind turbine, using additional structural elements which modify the original shape of the rotor in the form of multi-shaped bowls which change the airflow distribution. A three-dimensional CAD model of the tested wind turbine was presented, with three variants subjected to simulation: a basic wind turbine without the element that modifies the airflow distribution, a turbine with a plano-convex bowl, and a turbine with a centrally convex bowl, with the hyperbolic disappearance of convexity as the radius of the rotor increases. The momentary value of wind speed, recorded at measuring points located in the plane of wind turbine blades, demonstrated an increase when compared to the base model by 35% for the wind turbine with the plano-convex bowl, for the wind speed of 5 m/s, and 31.3% and 49% for the higher approaching wind speed, for the plano-convex bowl and centrally convex bowl, respectively. The centrally convex bowl seems to be more appropriate for higher approaching wind speeds. An increase in wind turbine efficiency, described by the power coefficient, for solutions with aerodynamic bowls was observed.

The paper presents the results related to the simulation of dust-separating tangential cyclones: single cyclones of various geometries, and an axial multi-cyclone with fixed geometries and components. Its goal was to apply low-cost analyses for cyclones in industrial realization. Therefore, the...