Honghua Wang

Mr. Honghua Wang

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 February 2020 in Polymers
Verified
Journal Article
Open access
PDF file
JSJiuqiang Song
Jiuqiang Song
ZHZhixiong Huang
Zhixiong Huang
YQYan Qin
Yan Qin
HWHonghua Wang
Honghua Wang
MSMinxian Shi
Minxian Shi
Ceramifiable silicone rubber composites play important roles in the field of thermal protection systems (TPS) for rocket motor cases due to their advantages. Ceramifiable silicone rubber composites filled with different contents of ZrSi2 were prepared in this paper. The fffects of ZrSi2 on the vulcanization, mechanical and ablation resistance properties of the composites were also investigated. The results showed that the introduction of ZrSi2 decreased the vulcanization time of silicone rubber. FTIR spectra showed that ZrSi2 did not participate in reactions of the functional groups of silicone rubber. With the increasing content of ZrSi2, the tensile strength increased first and then decreased. The elongation at break decreased and the permanent deformation increased gradually. The thermal conductivity of the composite increased from 0.553 W/(m·K) to 0.694 W/(m·K) as the content of the ZrSi2 increased from 0 to 40 phr. In addition, the thermal conductivity of the composite decreased with the increase of temperature. Moreover, thermal analysis showed that the addition of ZrSi2 increased the initial decomposition temperature of the composite, but had little effect on the peak decomposition temperature in nitrogen. However, the thermal decomposition temperature of the composite in air was lower than that in nitrogen. The addition of ZrSi2 decreased the linear and mass ablation rate, which improved the ablative resistance of the composite. With the ZrSi2 content of 30 phr, the linear and mass ablation rate were 0.041 mm/s and 0.029 g/s, decreasing by 57.5% and 46.3% compared with the composite without ZrSi2, respectively. Consequently, the ceramifiable silicone rubber composite filled with ZrSi2 is very promising for TPS.

19 March 2020 in Polymers
Verified
Journal Article
Open access
PDF file
QMQilin Mei
Qilin Mei
HWHonghua Wang
Honghua Wang
XCXiaocheng Chen
Xiaocheng Chen
YWYing Wang
Ying Wang
ZHZhixiong Huang
Zhixiong Huang
With the rapid development of thermal protection systems for the aerospace industry and power electronics, polyarylacetylene (PAA) resin plays an important role because of its good mechanical properties, high glass transition temperature (Tg), low water absorption, high char yield (Yc), and the fact that there is no byproduct released in the curing process. In order to further improve the thermal property of PAA based FRP for the thermal protection field, the introduction of a zirconium element into arylacetylene is promising. In this paper, zirconium modified arylacetylene (ZAA) resin was prepared by two-step synthesis. The FTIR analysis characterized its molecular structure and confirmed the products. The viscosity of ZAA was about 6.5 Pa·s when the temperature was above 120 °C. The DSC analysis showed that the ZAA had a low curing temperature, and its apparent activation energy was 103.86 kJ/mol in the Kissinger method and 106.46 kJ/mol in the Ozawa method. The dielectric constant at 1 MHz of poly(zirconium modified arylacetylene) (PZAA) was 3.4. The TG analysis showed that the temperatures of a weight loss of 5% (Td5) and char yield (Yc) at 800 °C of PZAA were 407.5 °C and 61.4%, respectively. The XRD results showed the presence of SiO2 and ZrO2 in the PZAA residue after ablation. The XRF results showed that the contents of SiO2 and ZrO2 in PZAA residual after ablation were, respectively, 15.3% and 12.4%. The SEM showed that the surface of PZAA after ablation had been covered with a dense and rigid ceramic phase composed of ZrO2 and SiO2. Therefore, the introduction of Zr into arylacetylene greatly improved the densification of the surface after ablation, and improved the heat resistant property.

26 April 2020 in Polymers
Verified
Journal Article
Open access
PDF file
QMQilin Mei
Qilin Mei
HWHonghua Wang
Honghua Wang
DTDanliao Tong
Danliao Tong
JSJiuqiang Song
Jiuqiang Song
ZHZhixiong Huang
Zhixiong Huang
Benzoxazine resin has been paid more attention in the fields of aviation, electronics, automobiles and new energy industries because of its excellent comprehensive performance. Further application is limited, however, by shortcomings such as high brittleness and high curing temperature. Furthermore, higher thermal stability is imperiously demanded in special areas. Incorporating both an acetylene group and silicon into the benzoxazine monomer is a promising possible solution to improve the curing processability, thermal properties and toughness of benzoxazine. In this paper, an acetylene-functional/silicon-containing benzoxazine monomer was prepared by two-step synthesis, and acetylene-functional benzoxazine was also prepared as a comparison. FTIR and 1H NMR confirmed the molecular structure of acetylene-functional/silicon-containing benzoxazine. Differential scanning calorimetry (DSC) analysis showed that the initial and peak degradation temperatures of acetylene-functional/silicon-containing benzoxazine were decreased by 21 °C and 18 °C compared with acetylene-functional benzoxazine, respectively. The apparent activation energy of the curing reaction of acetylene-functional/silicon-containing benzoxazine was 83.1 kJ/mol, which was slightly lower than acetylene-functional benzoxazine (84.7 kJ/mol). TGA results showed that the acetylene-functional/silicon-containing benzoxazine had a higher thermal stability than acetylene-functional benzoxazine. The temperatures of 5% weight loss of acetylene-functional/silicon-containing benzoxazine were 380 °C in nitrogen and 485 °C in air, and the char yield at 1000 °C was 80% in nitrogen and 21% in air, respectively. The results of mechanical properties showed that the impact strength of acetylene-functional/silicon-containing benzoxazine was higher than acetylene-functional benzoxazine by 35.4%. The tensile and flexural strengths of acetylene-functional/silicon-containing benzoxazine were slightly higher than that of acetylene-functional benzoxazine.

5 December 2019 in Polymers
Verified
Journal Article
Open access
PDF file
HWHonghua Wang
Honghua Wang
QMQilin Mei
Qilin Mei
YDYujie Ding
Yujie Ding
ZHZhixiong Huang
Zhixiong Huang
MSMinxian Shi
Minxian Shi
Diallyl orthophthalate (DAOP) prepolymer was investigated as a reactive plasticizer to improve the processability of thermoplastics. The rheology of blends of DAOP prepolymer initiated by 2,3-dimethyl-2,3-diphenylbutane (DMDPB) and polyphenylene oxide (PPO) was monitored during the curing process, and their thermal properties and morphology in separated phases were also studied. Differential scanning calorimetry (DSC) results showed that the cure degree of the reactively plasticized DAOP prepolymer was reduced with increasing PPO due to the dilution effect. The increasing amount of the DAOP prepolymer led to a gradual decrease in the viscosity of the blends and the rheology behavior was consistent with the chemical gelation of DAOP prepolymer in blends. This indicated that the addition of the DAOP prepolymer effectively improved processability. The phase separation occurring during curing of the blend and the transition from the static to dynamic mode significantly influences the development of the morphology of the blend corresponding to limited evolution of the conversion around the gel point.

3 September 2025 in Gels
Verified
Journal Article
Open access
PDF file
HWHonghua Wang
Honghua Wang
TGTianchen Gao
Tianchen Gao
XLXinyi Li
Xinyi Li
YHYuci Huang
Yuci Huang
JWJunjie Wang
Junjie Wang
DGDongyun Guo
Dongyun Guo
BaTi5O11 nanocrystals were synthesized via a sol–gel method employing different organic solvents. The influence of solvent choice on microstructure and photocatalytic performance was investigated through methylene blue (MB) degradation under UV light irradiation. The monoclinic BaTi5O11 nanocrystals were successfully synthesized, where solvent selection significantly affected their grain size and Brunauer–Emmett–Teller (BET) surface area. The BaTi5O11 nanocrystals synthesized using polyethylene glycol-200 (PEG-200) exhibited the highest BET surface area (9.78 m2/g) and smallest average pore size (17.8 nm). The BaTi5O11 nanocrystals also displayed a larger optical bandgap (3.61 eV), attributed to pronounced quantum confinement and surface effects. Consequently, the PEG-200-derived BaTi5O11 photocatalyst achieved complete MB degradation within 30 min under UV light irradiation. This enhanced performance was attributed to the high BET surface area providing abundant active sites. Furthermore, the BaTi5O11 nanocrystal photocatalyst maintained excellent reusability and stability over four consecutive cycles.

25 July 2026 in Gels
Verified
Journal Article
Open access
PDF file
HWHonghua Wang
Honghua Wang
ZXZherui Xing
Zherui Xing
XWXingran Wang
Xingran Wang
ZHZhixiong Huang
Zhixiong Huang
DGDongyun Guo
Dongyun Guo
The effect of drying, thermal decomposition, and sintering conditions during the sol–gel synthesis of BaTi5O11 nanocrystals was investigated to optimize levofloxacin (LEV) photodegradation. Sintering emerges as the dominant factor, and BaTi5O11 nanocrystals synthesized at 700 °C for 120 min exhibit the smallest grain size, highest specific surface area and abundant active sites, achieving 93.2% LEV degradation within 30 min under UV irradiation. In contrast, excessive sintering temperatures or time induce grain coarsening and size homogenization, which reduce surface area and active sites, thereby impairing photocatalytic performance. The optimized nanocrystals also efficiently degrade other antibiotic pollutants, including ciprofloxacin, norfloxacin, and tetracycline. Radical trapping experiments confirm that •OH is the primary reactive species. Photoluminescence and photoelectrochemical analyses reveal a competition between grain size variation and charge carrier dynamics; however, photocatalytic degradation underscores the dominant role of surface-active sites and specific surface area. Kelvin probe force microscopy (KPFM) further corroborates efficient charge separation, showing a cross-line contact potential difference (ΔVCPD) of approximately 90 mV, indicative of facile hole migration to the crystal surface. Collectively, these findings elucidate the processing–microstructure–property relationships in BaTi5O11 nanocrystals and provide a robust basis for the rational design of high-performance photocatalytic systems for antibiotic pollutant remediation.