Environmental management through effective utilization of biowastes has been a topic of intensive research in recent years. This study examines the effect of pyrolysis temperature on the physical and morphological characteristic of biochar (BC) derived from lignocellulosic wastes. The biochar was prepared by pyrolysing date palm biomass at various temperatures, i.e., 300, 400, 500, 600, and 700 °C. These pyrolysed biochars were then characterized for their carbon content, mineral compositions, chemical functionalities, and morphological structures, for understanding their physicochemical characteristics and microstructural evolution. It was revealed that the pyrolytic condition plays a key role in the formation of biochar microstructure. These biochar samples were then utilized without any further treatments/purifications for their practical application as reinforcement materials for polymer composites. They were blended with a polypropylene matrix by a melt mixing technique followed by injection molding process. The type of biochar was found to significantly affect the composites properties. Differences in microstructure, surface chemistry, and chemical compositions of BCs were observed to be determining factors affecting the compatibility and thermomechanical properties of resulted composites.
A tremendous potential has been observed in the designing of long afterglow materials for sensing, bioimaging, and encryption applications. In this study, two different strontium aluminate-based luminescent materials; SrAl2O4: Eu, Dy (S1), and Sr4Al14O25: Eu, Dy (S2) were melt-mixed with polypropylene (PP) matrix, and the phosphorescence properties were evaluated. After excitation at 320 nm, the PP/S1 composite exhibited a green emission and the PP/S2 generated a blue emission at 520 nm and 495 nm, respectively. The emission spectra intensity increased by increasing the content of these luminescent fillers. The attenuated total reflection-Fourier transform infrared (ATR-FTIR) experiments show that no chemical reaction occurred during the melt-mixing process. The differential scanning calorimetry (DSC) results revealed that the total crystallinity of the composites reduced by increasing the amount of the fillers; however, no changes in the temperature of melting (Tm) and crystallization (Tc) of PP were observed. Both fillers improved the impact strength of the composites, but the tensile strength (TS) and modulus (TM) decreased. Poly (ethylene glycol) dimethyl ether (P) plasticizer was used to improve the filler-matrix interaction and its dispersion; nevertheless, it adversely affected the intensity of the luminescence emissions.
Metal-plastic composites have the potential to combine enhanced electrical and thermal conductivity with a lower density than a pure metal. The drawback has often been brittleness and low impact resistance caused by weak adhesion between the metal filler and the plastic. Based on our observation that aluminum foil sticks very strongly to poly(ethylene terephthalate) (PET) if it is used as a backing during compression moulding, this work set out to explore PET filled with a micro and a nano aluminum (Al) powder. In line with other composites using filler particles with low aspect-ratio, the tensile modulus increased somewhat with loading. However, unlike most particle composites, the strength did not decrease and most surprisingly, the Izod impact resistance increased, and in fact more than doubled with certain compositions. Thus, the Al particles acted as a toughening agent without decreasing the modulus and strength. This would be the first case where addition of a metal powder to a plastic increased the modulus and impact resistance simultaneously. The Al particles also acted as nucleating agents but it was not sufficient to make PET crystallize as fast as the injection moulding polyester, poly(butylene terephthalate) (PBT).
24 January 2024 in Research on Chemical Intermediates
The first step of the DRM reaction is just the decomposition of CH4 into CH4−x (x = 1–4). The next step comprises two steps, namely the oxidation of CH4−x into syngas (by CO2) and the self-polymerization of CH4−x species. The earlier one is known as dry reforming of methane (DRM), and the latter one generates carbon deposits over the catalyst surface. In this study, we investigated the impact of 1–3 wt% Sr over Ni-based catalysts on a ZrO2-WO3 support on the catalytic activity and coke deposit. Various characterization techniques such as thermogravimetric analysis, X-ray diffraction, Raman spectroscopy, temperature-programed oxidation, temperature-programed reduction, and temperature-programed desorption were used to assess the physicochemical properties of the fresh and spent catalysts. The addition of 2wt% Sr promoter significantly improves the catalyst’s basicity in strong basic sites region through Sr2+ mediated interaction of CO2 species as well as inhibits the deposition of carbyne type carbon. Enhanced CO2 interaction results into the potential oxidation of carbon deposit and the highest CH4 conversion, reaching 60% up to 470 min TOS at a reaction temperature of 700 ℃. Graphical abstract
Dry reforming of CH4 was conducted over promoted Ni catalysts, supported on mesoporous gamma-alumina. The Ni catalysts were promoted by various metal oxides (CuO, ZnO, Ga2O3, or Gd2O3) and were synthesized by the incipient wetness impregnation method. The influence of the promoters on the catalyst stability, coke deposition, and H2/CO mole ratio was investigated. Stability tests were carried out for 460 min. The H2 yield was 87% over 5Ni+1Gd/Al, while the CH4 and CO2 conversions were found to decrease in the following order: 5Ni+1Gd/Al > 5Ni+1Ga/Al > 5Ni+1Zn/Al > 5Ni/Al > 5Ni+1Cu/Al. The high catalytic performance of 5Ni+1Gd/Al, 5Ni+1Ga/Al, and 5Ni+1Zn/Al was found to be closely related to their contents of NiO species, which interacted moderately and strongly with the support, whereas free NiO in 5Ni+1Cu/Al made it catalytically inactive, even than 5Ni/Al. The 5Ni+1Gd/Al catalyst showed the highest CH4 conversion of 83% with H2/CO mole ratio of ~1.0.