Przemyslaw Piotr Ptak

Prof. Dr. Przemyslaw Piotr Ptak

Gdynia Maritime University
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 June 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
SASkwarek Agata
Skwarek Agata
OKOliver Krammer
Oliver Krammer
HTHurtony Tamás
Hurtony Tamás
Przemyslaw Piotr PtakPrzemyslaw Piotr Ptak
Przemyslaw Piotr Ptak
Krzysztof GóreckiKrzysztof Górecki
Krzysztof Górecki
BIBalázs Illés
Balázs Illés
The properties of Sn99Ag0.3Cu0.7 (SACX0307) solder alloy reinforced with ZnO nanoparticles were investigated. The primary ZnO particle sizes were 50, 100, and 200 nm. They were added to a solder paste at a ratio of 1.0 wt %. The wettability, the void formation, the mechanical strength, and the thermoelectric parameters of the composite solder alloys/joints were investigated. Furthermore, microstructural evaluations were performed using scanning electron and ion microscopy. ZnO nanoparticles decreased the composite solder alloys’ wettability, which yielded increased void formation. Nonetheless, the shear strength and the thermoelectric parameters of the composite solder alloy were the same as those of the SACX0307 reference. This could be explained by the refinement effects of ZnO ceramics both on the Sn grains and on the Ag3Sn and Cu6Sn5 intermetallic grains. This could compensate for the adverse impact of lower wettability. After improving the wettability, using more active fluxes, ZnO composite solder alloys are promising for high-power applications.

1 December 2018 in Microelectronics Reliability
Verified
Journal Article
Closed access
Krzysztof GóreckiKrzysztof Górecki
Krzysztof Górecki
Przemyslaw Piotr PtakPrzemyslaw Piotr Ptak
Przemyslaw Piotr Ptak

1 December 2017 in Microelectronics Reliability
Verified
Journal Article
Closed access
Krzysztof GóreckiKrzysztof Górecki
Krzysztof Górecki
Przemyslaw Piotr PtakPrzemyslaw Piotr Ptak
Przemyslaw Piotr Ptak

28 March 2020 in Materials
Verified
Journal Article
Open access
PDF file
SASkwarek Agata
Skwarek Agata
Przemyslaw Piotr PtakPrzemyslaw Piotr Ptak
Przemyslaw Piotr Ptak
Krzysztof GóreckiKrzysztof Górecki
Krzysztof Górecki
HTHurtony Tamás
Hurtony Tamás
BIBalázs Illés
Balázs Illés
The effect of the microstructure of solder joints on the thermal properties of power LEDs is investigated. Solder joints were prepared with different solder pastes, namely 99Sn0.3Ag0.7Cu (as reference solder) and reinforced 99Sn0.3Ag0.7Cu–TiO2 (composite solder). TiO2 ceramic was used at 1 wt.% and with two different primary particle sizes, which were 20 nm (nano) and 200 nm (submicron). The thermal resistance, the electric thermal resistance, and the luminous efficiency of the power LED assemblies were measured. Furthermore, the microstructure of the different solder joints was analyzed on the basis of cross-sections using scanning electron and optical microscopy. It was found that the addition of submicron TiO2 decreased the thermal and electric thermal resistances of the light sources by 20% and 16%, respectively, and it slightly increased the luminous efficiency. Microstructural evaluations showed that the TiO2 particles were incorporated at the Sn grain boundaries and at the interface of the intermetallic layer and the solder bulk. This caused considerable refinement of the Sn grain structure. The precipitated TiO2 particles at the bottom of the solder joint changed the thermodynamics of Cu6Sn5 formation and enhanced the spalling of intermetallic grain to solder bulk, which resulted in a general decrease in the thickness of the intermetallic layer. These phenomena improved the heat paths in the composite solder joints, and resulted in better thermal and electrical properties of power LED assemblies. However, the TiO2 nanoparticles could also cause considerable local IMC (Intermetallic Compounds) growth, which could inhibit thermal and electrical improvements.

3 April 2018 in Soldering & Surface Mount Technology
Verified
Journal Article
Closed access
Krzysztof GóreckiKrzysztof Górecki
Krzysztof Górecki
BDBarbara Dziurdzia
Barbara Dziurdzia
Przemyslaw Piotr PtakPrzemyslaw Piotr Ptak
Przemyslaw Piotr Ptak
Purpose: This paper aims to present the results of the influence of a manner of soldering light emitting diodes (LEDs) to the metal core printed circuit board on thermal parameters of the module LED containing these diodes. Design/methodology/approach: Using the authors’ elaborated measuring method and the dedicated measurement set-up, transient thermal impedances of LED modules, mounted using different soldering processes and mounted to the heat-sink with different values of the moment of force, are measured. The obtained results of measurements are discussed. Findings: It was shown experimentally that the manner of soldering could strongly influence efficiency of dissipation of heat generated in the module. The best thermal properties were obtained for soldering using vapour phase technology with vacuum and paste LFS-216LT. It was also proved that the moment of force used while mounting the considered modules on the heat-sink can result in a change of the value of thermal resistance of this module exceeding even 12 per cent. Research limitations/implications: The investigations were performed for five LED modules operating at one, arbitrarily selected value of power dissipated in these modules mounted on the heat-sink of arbitrarily selected dimensions. Practical implications: The obtained results of measurements could be usable for designers of mounting processes of power LED modules. Originality/value: This paper presents the results of investigations of thermal properties of LED modules, in which different techniques of soldering are used. It was shown experimentally that the manner of soldering could strongly influence efficiency of dissipation of heat generated in the module. It was also proved that the moment of force used while mounting the considered modules on the heat-sink is important.

7 May 2019 in Energies
Verified
Journal Article
Open access
PDF file
Marcin JanickiMarcin Janicki
Marcin Janicki
TTTomasz Torzewicz
Tomasz Torzewicz
Przemyslaw Piotr PtakPrzemyslaw Piotr Ptak
Przemyslaw Piotr Ptak
TRTomasz Raszkowski
Tomasz Raszkowski
ASAgnieszka Samson
Agnieszka Samson
Paweł GóreckiPaweł Górecki
Paweł Górecki
Light-emitting diodes are nowadays the most dynamically developing type of light sources. Considering that temperature is the main factor affecting the electrical and lighting parameters of these devices, thermal models are essential subcomponents of the multidomain models commonly used for simulation of their operation. The authors investigated white power light-emitting diodes soldered to Metal Core Printed Circuit Boards (MCPCBs). The tested devices were placed in a light-tight box on a cold plate and their cooling curves were registered for different diode heating current values and various preset cold plate temperatures. These data allowed the computation of optical and real heating power values and consequently the generation of compact thermal models in the form of Foster and Cauer RC ladders. This also rendered possible the analysis of the influence of the considered factors on the compact model element values and their parametrization. The resulting models yield accurate values of diode junction temperature in most realistic operating conditions and they can be easily included in multidomain compact models of power light emitting diodes.