Qipeng Tang

Qipeng Tang

Auto-generated profile, based on publicly available information

Qipeng Tang

School of Artificial Intelligence and Automation, National Key Laboratory of Science and Technology on Multispectral Information Processing and Key Laboratory of Image Processing and Intelligent Control, Huazhong University of Science and Technology (HUST), Wuhan, China

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 December 2023 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
SZSai Zhang
Sai Zhang
ASAnwen Shen
Anwen Shen
XLXin Luo
Xin Luo
QTQipeng Tang
Qipeng Tang
ZLZicheng Li
Zicheng Li
Electric vehicles (EVs) mainly use permanent magnet synchronous motors (PMSMs) as the core power units. Moreover, when EVs navigate complex roads, the requirements become even more stringent. This paper addresses the real-time parameter estimation and state evaluation of PMSMs in EVs, considering the inevitable external interference. By leveraging the stability condition of the energy function, a simple adaptive scheme is proposed to enhance the robustness of PMSMs against current disturbances. At the same time, the online identification scheme for motor parameters is considered, which extends the practical application method of Lyapunov energy function stability. Subsequently, in order to optimize the current disturbance caused by parameter mismatch, the known model will be adjusted to the unknown model and the adaptive fuzzy scheme is introduced to discuss with the relevant parameters designed from the stability condition of the adaptive fuzzy Lyapunov energy function. Finally, the effectiveness of the proposed scheme in this paper is proved by various experiments.

4 April 2025 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SXSang Xu
Sang Xu
ASAnwen Shen
Anwen Shen
QTQipeng Tang
Qipeng Tang
MWMiaomiao Wang
Miaomiao Wang
PLPan Luo
Pan Luo
JXJinbang Xu
Jinbang Xu
Kalman filter (KF) is increasingly attracted for sensorless control of surface permanent magnet synchronous motors due to its strong robustness against measurement and system noise. However, the conventional method suffers from poor position and speed estimation accuracy under dynamic conditions and high computational cost. In order to solve these problems, an enhanced sensorless control strategy based on reduced-order linear Kalman filter (RLKF) cooperating with prediction error rolling compensation is introduced in this article. Differing from conventional methods, a reduced-order linear state equation encompassing rotor position, speed, and torque disturbance is constructed. Then, by obtaining the prediction error of system output using the motor current equation in the predictive reference frame, the optimal estimation of rotor position and speed in the KF algorithm is achieved based on the reduced-order model. This not only simplifies the calculation process but also enhances the position and speed estimation accuracy under dynamic conditions. Meanwhile, a prediction error rolling compensation algorithm is developed to minimize the estimation deviations caused by motor parameter variations. In addition, the system's dynamic performance is further improved with an adopted speed controller based on torque disturbance feedforward and acceleration feedback. Finally, experimental results verify the effectiveness and feasibility of the proposed strategy.

9 April 2024 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
QTQipeng Tang
Qipeng Tang
PLPan Luo
Pan Luo
SXSang Xu
Sang Xu
MSMinggang Sheng
Minggang Sheng
ASAnwen Shen
Anwen Shen
JXJinbang Xu
Jinbang Xu
Direct torque control (DTC) is increasingly attracted for high performance control of surface permanent magnet synchronous motors (SPMSMs) due to its easy implementation and fast dynamic response. However, the conventional switching-table-based method inevitably produces large torque and stator flux ripples because the selection of inverter's active-voltage vector is depending on the sign of torque and flux errors through hysteresis comparators regardless of their amplitude errors. To resolve these problems, a novel DTC strategy based on flux-torque decoupling is proposed in this paper. With the proposed method, two desired voltage vectors are firstly constructed to achieve the decoupling control of stator flux and torque by analyzing the relationships between applied voltage and torque and stator flux derivative. Afterwards, by applying vector synthesis to analyze the generation of two desired voltage vectors, the corresponding inverter's active-voltage vectors and their duty ratios are determined, so as to achieve the precise regulation of stator flux and torque with little ripples. Furthermore, in order to minimize the influence of machine parameters variations, a simple and real-time identification method for the ratio between permanent magnet flux linkage and stator inductance is presented. Finally, the experimental results indicate the effectiveness and feasibility of the proposed strategy

29 July 2025 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
YSYi Shen
Yi Shen
MZMingzhen Zhang
Mingzhen Zhang
RTRuochen Tai
Ruochen Tai
QTQipeng Tang
Qipeng Tang
XLXin Luo
Xin Luo
ASAnwen Shen
Anwen Shen
The unmeasurable gear backlash nonlinearity caused by mechanical wear in multimotor driving systems (MDSs) is inevitable, imposing challenges for the modeling and controller design. As a remedy, this work proposes a model predictive controller (MPC) to handle the unmeasurable backlash often encountered in dual-motor driving systems (DDSs). First, a control-oriented model with an observer is established to estimate the backlash torque. Accordingly, a constrained MPC is developed to minimize both the tracking error and vibrations. Therein, delay compensation is leveraged to decrease prediction lag. PI feedback is introduced to compensate for the steady-state error caused by the offset of the external observer. Based on the output of the proposed MPC, which is the sum of the torques for two motors, a time-varying-bias-torque (TVBT) scheme to save energy consumption is designed to compute the torque for each motor. Finally, experiments are conducted on DDSs to verify the effectiveness and superiority of the present MPC-TVBT.

11 October 2024 in IET Power Electronics
Verified
Journal Article
Open access
PLPeihe Li
Peihe Li
ASAnwen Shen
Anwen Shen
QTQipeng Tang
Qipeng Tang
XLXin Luo
Xin Luo
JXJinbang Xu
Jinbang Xu
Direct torque control with space vector modulation has been increasingly attracting emphasis for permanent‐magnet synchronous machine control, benefiting from a high dynamic response and low torque ripple. However, the rapid tracking performance of torque and stator flux linkage is gradually deteriorating as the machine enters the overmodulation region because of the output‐voltage limitation of the inverter. Therefore, to enhance the system tracking performance in the overmodulation region, an innovative overmodulation method based on torque and flux optimal tracking is proposed. In contrast to the conventional overmodulation method where only one of the torque and stator flux linkage tracking is considered, the proposed strategy first constructs the weightless cost function to achieve a trade‐off control between the torque and stator flux linkage. Then, by using an equivalent geometric path to intuitively express the weightless cost function, the minimum cost function can be easily solved and the optimal output voltage vector can be determined correspondingly, to achieve the fast‐tracking of both the torque and stator flux linkage. Additionally, the voltage utilization of different overmodulation schemes is also analysed. Finally, the experimental results demonstrate the efficiency and practicality of the proposed strategy.

14 June 2022 in IEEE Transactions on Industrial Informatics
Verified
Journal Article
Closed access
QTQipeng Tang
Qipeng Tang
YSYi Shen
Yi Shen
MSMinggang Sheng
Minggang Sheng
ASAnwen Shen
Anwen Shen
PLPan Luo
Pan Luo
JXJinbang Xu
Jinbang Xu
This paper proposes a novel rotational restart strategy based on the dead time adaptive expansion for the sensorless surface-mounted permanent magnet synchronous machines (SPMSMs) drive system. With the proposed method, the interval time of zero-voltage pulses (ZVPs) is replaced by the dead time and each pulse-width modulation (PWM) period consists of the dead time and action time of ZVPs. By regulating the dead time based on the stator-current amplitude feedback, the stator current can be controlled within the reasonable setting range, which not only can achieve the adaptive selection of the action time and interval time of ZVPs, but also avoid the potential overcurrent and overcome the current sampling noise. Meanwhile, aiming at two continuous and discontinuous current modes caused by the inserted dead time, the corresponding calculation expressions of the rotor position are deduced in detail. Finally, experimental results indicate the effectiveness and feasibility of the proposed strategy.