10 July 2020 in IEEE Journal of Solid-State Circuits
This article presents a four-level pulse-amplitude modulation (PAM4) quarter-rate clock and data recovery circuit (CDR). A quarter-rate linear phase detector (QLPD) is proposed to reduce the recovered clock jitter by removing the dithering jitter of the bang-bang PD. A self-biased phase-locked loop (PLL)-based multiphase clock generator (MCG) with a very wide loop bandwidth (around 600 MHz) is proposed to reduce the MCG power consumption and generate a low-jitter multiphase clock for the quarter-rate operation. Fabricated in a 40-nm CMOS process, the prototype achieves a bit efficiency of 0.46 pJ/bit at 32-Gb/s input data rate. The measured jitter tolerance (JTOL) at the bit error rate (BER) of <; 10 -12 is higher than 0.35 UIPP with the corner frequency at about 10 MHz. The measured integrated jitter of the 4-GHz recovered clock is 352.6 fs.
8 September 2023 in IEEE Journal of Solid-State Circuits
This article presents a four-level pulse amplitude modulation (PAM-4) receiver (Rx) with a jitter compensation clock and data recovery (JCCDR) for high-speed retimer application. The JCCDR can attenuate the jitter transfer (JTRAN) from the input PAM-4 signal to the recovered clock and data without sacrificing the jitter tolerance (JTOL) bandwidth. A jitter compensation circuit (JCC) is implemented within the JCCDR to support JTRAN detection, complementary signal generation, and JTRAN attenuation functions. Theoretical analysis is performed to verify the effectiveness and challenges of the proposed method. Prototyped in 40-nm CMOS, the Rx achieves error-free operation with PAM-4 input from 30 to 60 Gb/s. The JCCDR provides an ultralow $< -$ 8 dB JTRAN while maintaining a 40-MHz wide JTOL bandwidth with a 0.2-UIPP jitter amplitude. A jitter compensation ratio up to 60% can be supported from dc to 4 MHz.
25 October 2021 in IEEE Open Journal of the Solid-State Circuits Society
Today’s mixed-signal SoCs are challenging to validate. Running enough test vectors often requires the use of event-driven simulation and hardware emulation, which in turn necessitates the creation of analog behavioral models. This paper reviews different approaches proposed to address that modeling challenge, and shows how they can be divided by the methods used to solve for analog circuit values, represent analog waveforms, and validate analog functional models. We illustrate the power of these techniques as applied to a 16 Gb/s PHY, demonstrating a 10, $000\times $ speedup vs. SPICE simulation using event-driven models in Verilog simulation, and a further 5, $000\times $ speedup using synthesizable analog models in FPGA emulation.
14 September 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
The common mode (CM) current in differential circuits generates CM noise which radiates in the environment and causes electromagnetic interference (EMI) with electronic devices in proximity. This noise is generated due to imbalance in the charging and discharging paths of the driver circuit and asymmetric equalization. A systematic study of how asymmetric equalizer increase the CM noise is still lacking. Few active on-chip solutions are proposed for wireline transmitters up to 20-Gbps speed. However, these solution does not suppress CM noise by the equalizer and they could not support four-level pulse amplitude modulation (PAM-4) optical transmitters. This paper analyzes two potential sources of EMI-related CM noise, the common mode logic (CML) driver and feed forward equalization (FFE) circuit, and presents a novel on-chip active circuit technique for automatic CM noise cancellation in high-speed PAM-4 transmitter. This solution provides the benefits of small size and low cost by eliminating the need for discrete components to suppress EMI. The post-layout simulation demonstrates that the CM noise cancellation circuit (CMNC) efficiently mitigate the EMI by suppressing the CM noise up to 90% and consumes 5 mW, with core area of $17 \mu m \times 9 \mu m$ .
8 January 2021 in IEEE Open Journal of Circuits and Systems
This article presents a quarter-rate source-synchronous PAM-4 receiver for energy-efficient chip-to-module communication. A novel single-stage multiple peaking continuous-time linear equalizer (MP-CTLE) using feedback enabled multiple peaking scheme for both high-frequency equalization (HF-EQ) and low-frequency equalization (LF-EQ) is proposed to improve the BER performance and overall energy efficiency. The LF-EQ of the MP-CTLE eliminates the need for many DFE taps in SR/VSR applications to save power and area. A 1-tap feedforward equalizer (FFE) is used to further compensate for the high-frequency loss. We also use a ring oscillator based wide bandwidth phase-locked loop (WBW-PLL) as the multiphase clock generator (MPCG) in the clock and data recovery loop to save power with acceptable phase accuracy. Fabricated in 40-nm CMOS technology, the prototype receiver chip achieves error-free operation up to 52 Gb/s PAM-4 with superior bit efficiency of 0.126pJ/bit/s/dB while compensating 7.3-dB channel loss at 13GHz. With the proposed single-stage MP-CTLE, the receiver extends the error-free operation from PRBS-7 to PRBS-9. The BER bathtub curve at $10^{-6}$ is improved from 0.018 UI to around 0.1 UI.