8 March 2018 in Journal of Lightwave Technology
This paper presents an energy-efficient visible light communication (VLC) receiver system-on-a-chip (SoC) that employs ambient light rejection (ALR) and post-equalization techniques for emerging light fidelity (Li-Fi) applications using ordinary phosphorescent white light-emitting diodes (LEDs). A current-reuse transimpedance amplifier is proposed for energy-efficient applications. An ALR unit is implemented to eliminate the potential DC interference under strong ambient light. A two-stage continuous-time linear equalizer is utilized to compensate for the limited bandwidth of white LEDs, which is below 3 MHz. Implemented in a 0.18 μm CMOS process, the receiver occupies an area of 0.7 × 0.4 mm 2 and consumes 2.2 mW of power at 24 Mb/s from a 1.8 V power supply. An IEEE 802.15.7 PHY-II compliant Li-Fi link that employs the proposed receiver SoC and a custom transmitter SoC is demonstrated based on 1-W phosphorescent white LEDs without using blue filtering, achieving a bit error rate of 1 × 10 -9 for data rates up to 24 Mb/s over 1.6 m distance, and 22 Mb/s over 2.7 m distance, with on-off keying modulation and 2 11 -1 pseudorandom binary sequence (PRBS-11) optical inputs. The receiver SoC achieves a bit efficiency six times better than that of the prior art using off-the-shelf discrete components, and can tolerate an ambient light level of 3500 lx. A figure of merit accommodating the most important system parameters is also proposed for a comprehensive comparison of different VLC systems.
10 July 2020 in IEEE Journal of Solid-State Circuits
This article presents a four-level pulse-amplitude modulation (PAM4) quarter-rate clock and data recovery circuit (CDR). A quarter-rate linear phase detector (QLPD) is proposed to reduce the recovered clock jitter by removing the dithering jitter of the bang-bang PD. A self-biased phase-locked loop (PLL)-based multiphase clock generator (MCG) with a very wide loop bandwidth (around 600 MHz) is proposed to reduce the MCG power consumption and generate a low-jitter multiphase clock for the quarter-rate operation. Fabricated in a 40-nm CMOS process, the prototype achieves a bit efficiency of 0.46 pJ/bit at 32-Gb/s input data rate. The measured jitter tolerance (JTOL) at the bit error rate (BER) of <; 10 -12 is higher than 0.35 UIPP with the corner frequency at about 10 MHz. The measured integrated jitter of the 4-GHz recovered clock is 352.6 fs.
5 November 2020 in IEEE Journal of Solid-State Circuits
This article presents a leakage cancellation architecture for single-antenna frequency-modulated continuous-wave (FMCW) radars at W-band. A shared antenna for transmitter (TX) and receiver (RX) can substantially reduce the form factor, cost, and complexity of radar modules. Due to the simultaneous operation of the TX and RX in FMCW radars, employing a shared antenna will, however, significantly increase TX-to-RX leakage, resulting in RX saturation and desensitization. Our proposed cancellation scheme employs analog feedback to confine the TX leakage right at the RX input port, and thus, relieves the ongoing RX chain from saturation. The proposed single-antenna transceiver (TRX) prototype was fabricated in 65-nm CMOS technology with a die area of 1 mm². The output power of 2 dBm was achieved for the TX in a frequency range of 80-84 GHz. In addition, a conversion gain and noise figure of 45 and 15 dB was measured for the RX in the presence of the TX signal via a shared antenna port. TX-to-RX isolation of more than 45 dB was achieved in the operating W-band. The chip consumes 108 mW (80.5 mW for the TX and 27.5 mW for the RX) from a 1.2-V supply voltage. Moreover, the functionality of the single-antenna radar operation was verified by connecting the chip to an on-printed circuit board (PCB) 4x8 patch antenna array with a simulated gain of 15 dBi, implemented on RO3003 Rogers material. Using the single-antenna radar module as a demo system, a 40x50 cm² rectangular metallic plate was detected at a distance up to 19 m.
29 October 2020 in Journal of Lightwave Technology
Visible light communication (VLC) technology employing light-emitting diodes (LEDs) as light sources has the advantages of using the license-free spectrum, being power and cost-efficient and having high security. However, common LED devices feature narrow bandwidth, nonlinear optical and frequency responses over different injection current levels, which result in bandwidth limitation and signal distortion, especially under high order modulation such as 4-pulse amplitude modulation (PAM-4) with wide current swing. In view of this, a compact PAM-4 VLC transceiver system-on-a-module (SOM) employing a white LED as the light source with a pre- and a post-equalization is proposed. The white LED, consisting of a red, a green and a blue LED unit is driven by three separate drivers with feed-forward equalizers (FFEs). Each of the LED units contributes to one of the three eyes in the output PAM-4 optical signal. The three LED drivers with FFEs can be calibrated with digital and analog control to cancel the differences in optical and frequency responses of the three LED units. A three-stage continuous-time linear equalizer (CTLE) is used at the receiver side as post-equalization, which further compensates for the narrow LED bandwidth. The transmitter and receiver module occupy an area of 0.01 m2 and 0.0024 m2 respectively. Based on experimental results, the proposed system can improve the highest achievable data rate from 28 Mbps to 75 Mbps and achieve an extension ratio of 2.67 based on the pre- and post-equalizations.
8 September 2023 in IEEE Journal of Solid-State Circuits
This article presents a four-level pulse amplitude modulation (PAM-4) receiver (Rx) with a jitter compensation clock and data recovery (JCCDR) for high-speed retimer application. The JCCDR can attenuate the jitter transfer (JTRAN) from the input PAM-4 signal to the recovered clock and data without sacrificing the jitter tolerance (JTOL) bandwidth. A jitter compensation circuit (JCC) is implemented within the JCCDR to support JTRAN detection, complementary signal generation, and JTRAN attenuation functions. Theoretical analysis is performed to verify the effectiveness and challenges of the proposed method. Prototyped in 40-nm CMOS, the Rx achieves error-free operation with PAM-4 input from 30 to 60 Gb/s. The JCCDR provides an ultralow $< -$ 8 dB JTRAN while maintaining a 40-MHz wide JTOL bandwidth with a 0.2-UIPP jitter amplitude. A jitter compensation ratio up to 60% can be supported from dc to 4 MHz.
27 July 2020 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents a low-power 1/4-rate four-level pulse amplitude modulation (PAM4) receiver with an adaptive variable-gain rectifier (AVGR)-based decoder in 28-nm CMOS technology. The PAM4 input signal is preconditioned by a continuous-time linear equalizer (CTLE) then sampled into four branches of decoders by 1/4-rate clocks. The proposed AVGR-based PAM4-to-nonreturn-to-zero (NRZ) decoder performs gain adaptation and amplitude rectification simultaneously for decoding the least significant bit (LSB). The linear sense amplifier in the AVGR is modified from a latch to achieve a high gain and low power. Compared with the full-rate receiver adopting a decoder consisting of three comparators, this design achieves a better power efficiency by employing a 1/4-rate topology and merging a variable-gain function into the decoder. Experimental results demonstrate that the receiver chip can receive and decode a 24-Gb/s 190-mVpp PAM4 signal at a BER of 10⁻¹¹ and a bit efficiency of 1.38 pJ/bit.