1 October 2024 in APL Photonics
This paper reports on a monolithically integrated gallium arsenide (GaAs)-based photonic integrated circuit platform for wavelengths around 1064 nm. Enabled by spatially selective quantum well removal and two-step epitaxial growth, it supports on-chip gain as well as passive waveguides. In addition, shallow- and deep-etched waveguides are realized. The former result in waveguide losses of less than 2 dB/cm, while the latter enable compact integrated waveguide components. To demonstrate the performance of the platform, racetrack ring resonators based on deep-etched Euler bends and shallow-etched directional couplers are realized, achieving high intrinsic quality factors of 2.6 × 105 and 3.2 × 105 for the fundamental TE and TM mode, respectively. To demonstrate the use of these resonators, ring-resonator-coupled lasers are fabricated, resulting in one-sided output powers of up to 14 mW and single-mode operation with 40 dB side-mode suppression. The successful integration of ring resonators on a GaAs-based active/passive photonic integrated circuit platform paves the way for the realization of fully monolithic, widely tunable, and narrow linewidth ring-resonator-coupled laser sources.
30 December 2021 in IEEE Photonics Technology Letters
Distributed Bragg Reflector semiconductor lasers are ideally suited for quantum technology applications due to their high efficiency, small footprint, and tunability in combination with the frequency stability provided by an integrated frequency selective element. Here we present the design, fabrication, and electro-optical characterization of DBR lasers optimized for strontium-based quantum technology applications at 689.449 nm. The devices achieved an optical output power of up to 88 mW, four times more than previously reported, as well as a spectral linewidth of 0.4 MHz.
14 April 2022 in IEEE Photonics Journal
Progress in epitaxial design is shown to enable increased optical output power P opt and power conversion efficiency η E and decreased lateral far-field divergence angle in GaAs-based distributed Bragg reflector (DBR) broad-area (BA) diode lasers. We show that the wavelength-locked power can be significantly increased (saturation at high bias current is mitigated) by migrating from an asymmetric large optical cavity (ASLOC) based laser structure to a highly asymmetric (extreme-triple-asymmetric (ETAS)) layer design. For wavelength-stabilization, 7 th order, monolithic DBRs are etched on the surface of fully grown epitaxial layer structures. The investigated ETAS reference Fabry-Pérot (FP) BA lasers without DBRs and with 200 µm stripe width and 4 mm cavity length provide P opt = 29 W (still increasing) at 30 A in continuous-wave mode at room temperature, in contrast to the maximum P opt = 24 W (limited by strong power saturation) of baseline ASLOC lasers. The reference ETAS FP lasers also deliver over 10% higher η E at P opt = 24 W. On the other hand, in comparison to the wavelength-stabilized ASLOC DBR lasers, ETAS DBR lasers show a peak power increment from 14 W to 22 W, and an efficiency increment from 46% to 60% at P opt = 14 W. A narrow spectral width (< 1 nm at 95% power content) is maintained across a very wide operating range. Consistent with earlier studies, a narrower far-field divergence angle and consequently an improved beam-parameter product is also observed, compared to the ASLOC-based lasers.
11 August 2022 in Semiconductor Science and Technology
We report on the fabrication and electro-optical performance of ridge waveguide (RW) lasers emitting near 905 nm based on a vertical layer structure consisting of three single quantum wells (SQWs) as active regions separated by two tunnel junctions (TJs). The single waveguide core is designed in such a way that the third vertical mode is lasing. The width of the ridge is varied between 3 µm and 200 µm. Deep- and shallow-etched ridges were fabricated. The shallow etching stopped slightly above the topmost SQW, whereas the deep etch went through all TJs and stopped slightly above the lowest SQW. For comparison, we also fabricated conventional shallow-etched RW lasers based on a similar vertical structure having only one SQW and no TJs. The TJ RW lasers with deep-etched ridges provide the highest output power, lowest threshold current and best slope efficiency of 2.4 W A−1 for a ridge width of 6 µm. The performance of shallow-etched TJ RW lasers is lowest for small ridge widths but surpasses the performance of the conventional RW lasers when the ridge width is increased. The lateral far field angle of deep-etched TJ RW lasers is about 2° larger compared to the shallow etched ones.
10 December 2019 in IEEE Photonics Technology Letters
3 September 2024 in IEEE Journal of Selected Topics in Quantum Electronics
For LiDAR applications, compact, robust, and mass-producible light sources generating high-peak power nanosecond-long pulses are essential. This paper presents an investigation of power scaling in semiconductor lasers via the number of epitaxially stacked active regions in a single vertical waveguide supporting a higher order mode, chip length, output aperture width, and lateral waveguide design. All devices are wavelength-stabilized using surface gratings integrated either as a passive section at the rear facet of the diode laser as a distributed-Bragg-reflector (DBR) or along the full length of the chip in a distributed feedback (DFB) design. A 4 mm long broad-area (BA) DBR laser with a stripe width of 200 $\mu$ m and five active regions delivered approximately 171 W at 80 A, a factor of 6.6 more peak pulse power than the standard 6 mm long single active region DBR laser with 50 $\mu$ m stripe width. A corresponding 3 mm long 3-active region DFB-BA laser achieved more than 125 W at 129 A. These BA lasers have a lateral beam propagation ratio M $^{2}\approx$ 30. In contrast, weakly tapered ridge waveguide (TRW) lasers were found to generate more than 20 W with an M $^{2}$ of about 3 and an excellent lateral brightness of 24 W $\cdot$ mm $^{-1}$ mrad $^{-1}$ .