This letter experimentally demonstrates 1.2 kV normally-off p-GaN gate lateral high-electron-mobility transistors (HEMTs) on 200 mm diameter engineered substrates. The fabricated p-GaN gate HEMT with optimum gate-drain spacing exhibits a threshold voltage (V th ) of 3.2 V, an ON/OFF ratio of 10 8 , low specific ON-resistance (R on,sp ) of 5.8 mΩ-cm 2 and hard breakdown voltage (V bd ) at 1800 V. Optimized devices also show good wafer scale uniformity (σ Ron = 1.2%) for the evaluated electrical parameters and passed on-wafer high temperature gate bias (HTGB) and reverse bias stress tests without device failures.
12 July 2019 in ECS Journal of Solid State Science and Technology
We present a detailed study on fabrication and characterization of Ge/GeSn heterojunction p-type tunnel-field-effect-transistors (TFETs). Critical process modules as high-k stack and p-i-n diodes are addressed individually. As a result an ultrathin equivalent oxide thickness of 0.84 nm with an accumulation capacitance of 3 μF/cm 2 was achieved on an extremely scaled tri-layer stack of GeSnOx/Al 2 O 3 /HfO 2 deposited by atomic-layer deposition monitored in situ by spectroscopic ellipsometry. Combining these process modules, Ge/GeSn heterojunction pTFETs are fabricated and characterized to demonstrate the best in-class pTFET performance in the GeSn material system. The transfer characteristics of the TFETs show signatures of the trap-assisted thermal generation in the subthreshold regime which is explained by a modified Shockley- Read-Hall model. For the ON-state current, we used band-to-band tunneling models calculated using parameters from the density functional theory. We then use the calibrated model to project performance of GeSn pTFETs with increased Sn content (lower bandgap), reduced trap density and ultrathin body geometry. Both experimental and projected results are benchmarked against state-of-the art III-V (e.g., In 0.65 Ga 0.35 /GaAs 0.4 Sb 0.6 ) pTFETs. We demonstrate the ability of GeSn to achieve superior performance with both high ON-current and sub-60 mV/decade switching benefiting from the small and direct bandgap for higher Sn contents.
16 October 2018 in Semiconductor Science and Technology
The electrical and optical material properties of epitaxial Ge 1−x Sn x and Si y Ge 1−x−y Sn x are of high interest for novel device applications. However, the limited Sn solubility in Ge makes the epitaxial growth of Ge 1−x Sn x and Si y Ge 1−x−y Sn x challenging. Most of the literature describing the epitaxial growth is for Ge 2 H 6 and SnCl 4 as Ge and Sn precursors, respectively. A more recent publication deals with the epitaxial growth of high-quality Ge 1−x Sn x with the more conventional GeH 4 . In this manuscript, we compare the structural and optical material quality of Ge 1−x Sn x , epitaxially grown on Ge virtual substrates as a function of growth pressure, growth temperature, the choice of the carrier gas (H 2 or N 2 ) and the choice of the Ge precursor (GeH 4 versus Ge 2 H 6 ). The best material quality in terms of surface morphology and photoluminescence characteristics is obtained if GeH 4 is used as a Ge precursor. For Ge 1−x Sn x grown with Ge 2 H 6 and at atmospheric pressure, pyramidical defects can be seen and there is a risk for uncontrolled local Sn agglomeration. The pyramidical defects are not observed on Ge 1−x Sn x layers grown at reduced pressure, but the highest achievable substitutional Sn concentration is lower. No pyramidical defects are found for Ge 1−x Sn x layers grown with GeH 4 and the issue of uncontrolled local Sn agglomeration does not appear.
In this work, we demonstrate the epitaxial growth of a gallium-nitride (GaN) buffer structure qualified for 1200 V applications on 200 mm engineered poly-AlN substrates with hard breakdown >1200 V. The manufacturability of a 1200 V qualified buffer structure opens doors to high voltage GaN-based power applications such as in electric cars. Key to achieving the high breakdown voltage is careful engineering of the complex epitaxial material stack in combination with the use of 200 mm engineered poly-AlN substrates. The CMOS-fab friendly engineered poly-AlN substrates have a coefficient of thermal expansion (CTE) that closely matches the CTE of the GaN/AlGaN epitaxial layers, paving the way for a thicker buffer structure on large diameter substrates, while maintaining the mechanical strength of the substrates and reaching higher voltage operation.