This study aims to investigate the mechanical properties of bamboo apus (gigantochloa apus) as a natural reinforced composite material. Bamboo’s laminates of gigantochloa apus were used as reinforcement on the epoxy resin matrix. The parameters examined in this study are the configuration of lamina and compaction pressure. Laminate configuration varies in the number, thickness and direction of the lamina. Compaction pressures of 1.5 MPa, 2 MPa, and 2.5 MPa were used to fabricate the Laminated Bamboo Composites (LBCs). The stem of bamboo with a length of 400 mm was split to obtain bamboo lamina with a size of 400×20 mm. The thickness of bamboo lamina is varied between 1 mm, 1.5 mm, and 2 mm. The bamboo lamina is then preserved by watering it with a preservative solution in the form of 2.5 % sodium tetraborate solution and dried in an oven until the water content reaches 10 %. LBCs were made with a hand lay-up method. After the LBCs were molded, they were pressed with 3 variations of dies compaction 1.5 MPa, 2 MPa and 2.5 MPa. The tensile and bending tests were carried out on the LBCs. Tensile testing is performed in accordance with ASTM standard D3039 and the bending tests were conducted based on ASTM standard D7264. The results show that at each compaction pressure, the highest tensile and bending strength was achieved by LBCs with a thickness of 1 mm of bamboo lamina and 7 layers of bamboo laminates. The LBC with thinner bamboo lamina reinforcement and more layers has the highest tensile strength and bending strength, even it has a lower mass fraction. The LBCs with laminates oriented 0° exhibited greater tensile and bending strengths than the LBCs with laminates structured –45°/+45° and 0°/90°. The LBCs with the 0° laminates direction is matrix fracture followed by lamina fracture. In the 0°/90° direction, matrix fracture is followed by delamination in the 90° and 0° laminates direction. Delamination and lamina clefting were observed in LBCs with laminates oriented +45°/–45°.
Developing efficient and reliable gas sensors for the simultaneous detection of multiple gases is paramount in various fields, specifically healthcare, biological, and biomedical applications. In this study, we present a novel ratiometric optical dual gas sensor based on perovskite quantum dots (PQDs) to detect nitric oxide and oxygen simultaneously. All dye molecules were excited using a 405 nm LED in the experimental setup. The results obtained from the experiments reveal that both the optical NO and O2 sensors exhibit linear Stern–Volmer plots, and the sensitivities observed for NO and O2 sensors were approximately 2.4 and 2.8, respectively. The response and recovery times of the optical NO sensor are 67 s and 69 s, respectively. O2 sensor response and recovery times are 66 s and 68 s, respectively. In this work, the ratiometric optical dual gas sensing approach suppressed the effects of spurious fluctuations in the intensity of external and excitation sources.
Induction hardening (IH) is a popular choice for automotive components such as camshafts for its ability to harden portions of a component selectively. The camshaft will contact the tappet, connected to the rocker arm, to open and close the valve whenever the engine is running. This contact between the camshaft and the tappet causes wear on the camshaft surface. IH of the camshaft is required to improve wear resistance and service life, as well as core elasticity to absorb high torsional stresses. It is known that studies about IH on camshafts are still very limited. This study aims to determine the effect of the induction hardening and tempering treatment on the mechanical properties of the camshaft made of HQ 705 steel. The induction hardening carried out in this study uses different parameter settings such as heating time and output current. The camshaft specimen is hardened by static induction and then quenched in oil. The specimens are tempered after induction hardening with different temperatures and holding times to adjust the hardness level and reduce brittleness. Hardness, macro photographs, micrograph, and wear tests were conducted to determine the mechanical properties of the camshaft specimen after the induction hardening and tempering process. This study indicates that induction hardening with an output current of 747 A for 15 seconds followed by tempering at 150 °C for 15 seconds on specimen 1 produced the best mechanical properties. On the surface of these specimens found more martensite content while there was no microstructural change on the inside. The surface hardness of these specimens is 44 HRC (Rockwell C Hardness), while the inside is 26 HRC. Meanwhile, specific wear decreased by 45.45%.
The pump shaft generally exposed either to liquids, which pumped continuously, or in certain locations along the shaft. The shaft material is Duplex Stainless Steel AISI 329H (UNS S32900). The purpose of this study is to determine the failure of the seawater pump shaft used in the engine cooling system on the ship anchor Handling Tug Supply (AHTS). Visual observation is the study of SWCP (Sea Water Cooling Pump) shaft material. The SEM test used to determine the initial crack (crack initiation). The EDS test used for chemical composition and the Brinell Hardness Tester hardness test also used to determine material hardness. Voltage analysis used to find out how much load received by the shaft. These five tests support in analyzing pump shaft failure. The conclusion of this failure analysis is that the shaft material has porosity. Fatigue cracks originate from the outer surface area of the shaft.