22 December 2017 in IEEE Transactions on Electromagnetic Compatibility
An equivalent two terminal model based on the Thevenin equivalents describes the common mode (CM) currents on the input and output side of two widely used types of dc-to-dc power converters—buck and boost. Thus, it describes a nonlinear circuit by a linear equivalent circuit. The maximized spectrum of the CM currents is extracted for converters with stochastic signals using a novel characterization procedure. The extracted Thevenin model is used in co-simulation combined with a full-wave electromagnetic solver to predict the radiated emissions from the system consisting of the shielded dc–dc converters with attached cables and a DC brushless motor as load. The results using the terminal model agree well with the measurements providing that the actual CM loads are within the range of CM loads used while obtaining the Thevenin equivalent circuit.
3 January 2018 in IEEE Transactions on Electromagnetic Compatibility
KPKeerthana Pamidimukkala
+4
Testing and debugging of electrostatic discharge (ESD) or electrical fast transient issues in modern electronic systems can be challenging. The following paper describes the design of an on-chip circuit that detects and stores the occurrence of a fast transient stress event at the ESD protection structures in an input/output pad. Measurements and simulations of a test chip in 90 nm technology show that this circuit can accurately detect and record the presence of a transient stress event with a peak current as low as 0.9 A or a duration as short as 1 ns, and that the detector works well across typical temperature and process variations. The small size of the detector allows it to be used effectively in low-cost commercial integrated circuits. The detector was tested in a system-level environment and successfully records transient events. The importance of simulating with intelligent approximations of the system parasitics is described and demonstrated in measurements. An improved detector is discussed, which performs better in terms of process variations.
16 May 2019 in IEEE Transactions on Electromagnetic Compatibility
A new method is developed to predict the scaling of the electromagnetic interference from a large system if similar subsystems are added. The method gives the predicted emission from multiple radiators as well as the level of certainty of the estimation. The proposed statistical approach is based on the phased array antenna theory and Monte Carlo simulation for a router with several line cards (N) and optical modules inserted. To validate the method, a large router with 498 optical modules with an unwanted radiation at 10.31 GHz was investigated in two different cases: the same frequency and different frequency per radiating subsystem. Several statistical experiments were performed for the proposed problem. The effect of phase and amplitude variations over the radiators is reported in this paper. The method is useful when it is not practical to assemble extraordinary amounts of identical hardware in a product installation. The results indicate the existence of a 10 log N (dB) tendency for the maximum electric field emission in a system radiating at the same frequency with random phase distribution over the radiators. For different frequency subsystems, the slope of the maximum electric field emission is lower than the 10 log N (dB) formula.
5 March 2018 in IEEE Transactions on Electromagnetic Compatibility
A terminal model is a common method to create equivalent models of dc-dc converters in order to predict conducted emissions. In this paper, a characterization method for converters with stochastic behavior is presented. The averaged and maximized spectra of the measured voltages and currents are used to create the model. The phase information is obtained using a dedicated reference channel. After the equivalent source was determined, the actual induced noise voltage at the test load was compared to that predicted by the model with the averaged and maximized spectra to estimate its accuracy. The results indicate that the agreement with the direct measurement is between 10 dB and 100 MHz.
7 August 2019 in IEEE Transactions on Electromagnetic Compatibility
Electrostatic discharge (ESD)-induced soft failures are a critical issue for electronic systems as the failures are mostly found after the hardware design is completed. Any changes applied to the hardware may delay the project. Diagnostic tools capable of identifying soft failure-induced malfunctions in an early stage of product design help to reduce the risk of late stage ESD-induced project delays. In many cases, soft failures can be directly observed by the user interface, system crash, or other obvious indicators. However, in an early product design stage the operation system may be marginal and applications may not be available. To improve the ability to detect soft failure critical design choices, this paper presents several methods to identify ESD-induced changes which may not be observable via direct observation. These methods include the observation of ac or dc currents, monitoring dc voltages, capturing near fields and processing them via short-term fast fourier transform (FFT), wavelet transformation, down mixing to audible range, and monitoring for latch-up via thermal imaging. The paper introduces the basis of each method, shows examples, and compares them for their detection ability.
16 April 2019 in IEEE Transactions on Electromagnetic Compatibility