Shih-Hung Chen

Shih-Hung Chen

Auto-generated profile, based on publicly available information

Shih-Hung Chen

IMEC, Leuven, Belgium

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2021 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
XTXinyan Tang
Xinyan Tang
YLYao Liu
Yao Liu
GMGiovanni Mangraviti
Giovanni Mangraviti
ZZZhiwei Zong
Zhiwei Zong
KKKhaled Khalaf
Khaled Khalaf
PWPiet Wambacq
Piet Wambacq
This article presents practical design considerations and methodologies for a 28-GHz front-end module (FEM) in 22-nm fully depleted silicon on insulator (FD-SOI) CMOS technology for the fifth generation (5G) wireless communication. The design adopts a gain-boosting technique that is comprehensively analyzed with a transformer-based stacked-FET power amplifier (PA). Then, the co-design of the transmit/receive (T/R) switch with the PA and low-noise amplifier (LNA) is investigated, and an electrostatic-discharge (ESD)-aware T/R switch incorporating PA circuitry is proposed to leverage the Tx- and Rx-mode performance. Moreover, the robustness of standalone PA and Tx-mode FEM is simulated and experimentally verified. Furthermore, the ground return paths and supply parasitic paths of the adopted single-ended LNA together with the proposed T/R switch are studied, properly simulated, and assessed. Finally, the proposed PA topology is first verified standalone, exhibiting 32-dB power gain ( $G_{p}$ ), an 18.2-dBm output 1-dB compression point (OP 1 dB ), and a 31.1% power-added efficiency (PAE) at OP 1 dB (PAE 1 dB ). Using this PA in the FEM yields a Tx-mode OP 1 dB /PAE 1 dB of 16 dBm/19.4%, and an average output power (Pout avg )/PAE of 10.1 dBm/8.3% for a 100-MHz bandwidth 256-QAM single-carrier signal at an error-vector magnitude (EVM) of −30 dB. In the Rx mode, noise figure (NF) and input-referred third-order intercept point (IIP3) are 3.2 and −5.4 dBm, respectively. A 2-kV human-body model (HBM) ESD protection of the FEM is predicted in transient simulations and measured with transmission line pulse (TLP) tests.

29 May 2020 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
WWWei-Min Wu
Wei-Min Wu
MKMing-Dou Ker
Ming-Dou Ker
SCShih-Hung Chen
Shih-Hung Chen
JCJie-Ting Chen
Jie-Ting Chen
DLDimitri Linten
Dimitri Linten
GGGuido Groeseneken
Guido Groeseneken
In order to meet the requirement of ultrahigh-speed, low latency, and wide bandwidth (BW) in the next 5G mobile network and internet of things (IoT) applications, the parasitic capacitance specification of electrostatic discharge (ESD) protection devices should become much stricter. Reducing the capacitance always degrades the ESD performance in terms of shrinking the size of the ESD protection device. The distributed ESD protection network is one of the solutions which mitigates the capacitance issue and provides a broadband design. However, while the ESD devices are put under the I/O pad in the distributed ESD protection network, back-end-of-line (BEOL) capacitance starts to play an important role in the advanced 28-nm CMOS process. Therefore, a tapered metal structure is proposed to significantly reduce 30% BEOL capacitance of the ESD device, which can gain a 2.8-GHz increase in the operational BW in the distributed network. Meanwhile, it can enhance the human-body-model (HBM) level up to 16% higher than the original layout style under the same front-end-of-line (FEOL) layout size.

5 May 2011 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
AGAlessio Griffoni
Alessio Griffoni
SCShih-Hung Chen
Shih-Hung Chen
STSteven Thijs
Steven Thijs
BKBen Kaczer
Ben Kaczer
JFJacopo Franco
Jacopo Franco
GGGuido Groeseneken
Guido Groeseneken
The OFF-state degradation of n-channel laterally diffused metal-oxide-semiconductor (MOS) silicon-controlled-rectifier electrostatic-discharge (ESD) devices for high-voltage applications in standard low-voltage complementary MOS technology is studied. Based on experimental data and technology computer-aided design simulations, impact ionization induced by conduction-band electrons tunneling from an n+ poly-Si gate to an n-well is identified to be the driving force of device degradation. Device optimization is proposed, which improves both OFF-state and ESD reliability.

25 January 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
WWWei-Min Wu
Wei-Min Wu
MKMing-Dou Ker
Ming-Dou Ker
SCShih-Hung Chen
Shih-Hung Chen
ASArturo Sibaja-Hernandez
Arturo Sibaja-Hernandez
SYSachin Yadav
Sachin Yadav
GGGuido Groeseneken
Guido Groeseneken
Gallium nitride (GaN) technologies have become an essential role in commercial advanced RF systems, which accompany emerging RF electrostatic discharge (ESD) reliability challenges. As opposed to ESD clamp transistors in LV CMOS technologies, a mis-correlation between standard-defined human body model (HBM) ESD robustness and commonly used TLP failure current was observed in GaN (MIS) high electron mobility transistors (HEMTs). Using transient HBM ${I}$ – ${V}$ characteristics, a novel discharge model is proposed to explain the transient discharge mechanism. The TCAD and SPICE simulations confirmed that the observed mis-correlation between TLP and HBM is attributed to 2-dimensional electron gas (2DEG) resistance modulation in response to HBM ESD transient voltage waveforms. The HBM waveforms under full transient duration in terms of rising and falling edges are further discussed. Eventually, the failure mechanisms in the TLP IVs and the HBM transient IVs can be well correlated in GaN (MIS)HEMTs.

19 July 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
WCWen-Chieh Chen
Wen-Chieh Chen
SCShih-Hung Chen
Shih-Hung Chen
TCThomas Chiarella
Thomas Chiarella
GHGeert Hellings
Geert Hellings
DLDimitri Linten
Dimitri Linten
GGGuido Groeseneken
Guido Groeseneken
In this work, the electrostatic discharge (ESD) reliability of the OFF-and ON-state NMOS field-effect transistors in a bulk FinFET technology are investigated. The impacts of source and drain epitaxy influenced by the gate pitch (GP) and the gate length ( $\textit{L}_{\textit{g}}$ ) are studied. In the OFF-state NMOSFET, which is known as grounded-gate NMOS (ggNMOS), the large GP introduces nonuniform epitaxy on source and drain, which cause high power density localization in device. The large $\textit{L}_{\textit{g}}$ effectively helps the ESD performance of ggNMOS in ways of better turn-on and contact current uniformity. The ON-state NMOSFET as an active power-rail clamp is also studied in 3-D TCAD simulations. The device shows little difference to transient responses, while the clamping voltage can be different with $\textit{L}_{\textit{g}}$ and GPs. With the same gate space, the short $\textit{L}_{\textit{g}}$ device has a lower clamping voltage and ON-resistance, which reduces oxide breakdown risk and achieves better ESD performance.

27 June 2023 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
WWWei-Min Wu
Wei-Min Wu
SCShih-Hung Chen
Shih-Hung Chen
CSChun-An Shih
Chun-An Shih
BPBertrand Parvais
Bertrand Parvais
NCNadine Collaert
Nadine Collaert
GGGuido Groeseneken
Guido Groeseneken
Gallium nitride (GaN)-on-Si technologies for advanced RF applications have been raising the attentions in semiconductor industries, which accompany with RF electrostatic discharge (ESD) reliability challenges. Both positive and negative ESD stress polarities are equally important to be investigated. Four scenarios of the positive and negative human body model (HBM) stresses on a gate-tied-to-source configuration ( GSMIS-HEMT ) and a gate-tied-to-drain configuration ( GSMIS-HEMT ) were conducted in GaN-on-Si MIS-HEMTs. A failure mechanism unveiled in the negative GSMIS-HEMT , which is different from the constant-power 2DEG failure mechanism in the typical positive GSMIS-HEMT , was demonstrated by the measured HBM transient I-V characteristics and the subsequent DC I-V traces. The specific ON-state failure mechanism is related to the constant-voltage gate dielectric failures, resulting from a unique HBM discharge mechanism without the existence of depletion region in the 2DEG channel. This causes the degradation of the HBM failure voltages on the devices. Thus, the lower HBM failure powers are required to destroy the gate dielectric layer, as compared to the high failure powers to induce the 2DEG burnouts.