Secondary-cast aluminum alloys have increasing industrial applications. Their biggest deficiency is their impurity content, especially Fe, which has low solubility in Al and almost all the content creates intermetallic phases. This work examines the effect of higher Fe content on the microstructure and properties of A356.0 alloy. At the same time, no other possibility existed to affecting the brittleness of the formation of the β phases. The calculation of Fecrit, ratio of Mn/Fe, quantitative and computed tomography analysis of porosity and Fe plate-like phases, measurement of mechanical and fatigue properties, and fractography analysis were performed in this study. The results show that gravity die casting into a sand mold, and the non-usage of Mn addition or heat treatment, do not have a negative effect on increasing the size of the Fe-rich plate-like phases. The longest Fe-rich phases have limited the pore growth and ratios, but their higher thickness led to greater porosity formation. The mechanical and fatigue properties correlate with the Fecrit level and the highest were for the experimental alloy with 0.454 wt.% of Fe. The experimental results confirmed the fact that if the Fe plate-like phases have a length of up to 50 µm, the fatigue properties depend more on the size of porosity. If the length of the Fe needles is more than 50 µm, then the properties are mainly affected by the length of these Fe phases.
14 July 2025 in The International Journal of Advanced Manufacturing Technology
This study investigates the microstructural evolution and mechanical property changes in the heat-affected zone (HAZ) of welded S960MC advanced high-strength steel (AHSS). The main objective was to evaluate the influence of welding thermal cycles on the microstructure and mechanical properties of different HAZ subzones, including the subcritical heat-affected zone (SCHAZ), intercritical heat-affected zone (ICHAZ), and fully transformed subzones (FGHAZ, CGHAZ, and FZ). Real welds were performed on 3 mm thick S960MC steel with metal-cored arc welding (MCAW), and thermal cycles specific to each subzone were simulated to study the resulting microstructures. Microhardness and tensile testing were conducted, and microstructural characterization was performed using electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and visual light microscopy (VLM). The SCHAZ exhibited carbide precipitation within the martensitic structure, resulting in a mixture of tempered martensite and bainite, with a smooth decrease in microhardness from 330 HV0.5 to 269 HV0.5. The ICHAZ, exposed to temperatures between Ac1 and Ac3, underwent partial austenitization, followed by transformation into a mixture of ferrite, bainite, and martensite, with a significant reduction in microhardness to 234 HV0.5 at its center. The fully transformed subzones showed grain coarsening, with microhardness varying from 284 HV0.5 in the CGHAZ to 319 HV0.5 in the FGHAZ and decreasing to 276 HV0.5 in the fusion zone. The ICHAZ was identified as the most critical subzone, exhibiting the highest susceptibility to mechanical failure.
The article is focused on the analysis of the structure and fracture surface of aluminum alloy specimens. Aluminum alloy AlMg9 was mainly used as an experimental material. The material from which specimens were made was supplied as cast without heat treatment, and specifically the material was produced by the continuous casting method. The structure of the test material was examined using a Neophot 32 optical microscope, and the fracture surface of the test specimen was examined using a scanning electron microscope (SEM). The fatigue life of the aluminum alloy was tested by method of a three-point bending cyclic loading using the parameters-frequency f = 100 Hz, temperature T = 22 ± 5 ℃ and stress ratio R = 0.11. The analysis showed that cast aluminum alloys are very sensitive to casting defects, such as porosity or the content and distribution of intermetallic phases. If large pores or phases are present on or near the surface of the sample, this can be the dominant cause of fatigue crack initiation and reduction of the fatigue lifetime.
1 August 2023 in Management Systems in Production Engineering
This study deals with the research on the impact of the construction of a tire-building drum on the selected parameters of a passenger tire. The introductory part of the study deals with a comprehensive analysis of the production process and factors that affect the quality of the final tire product during production. The content of this analysis is also the naming of problematic parts and their subsequent influence on the resulting parameters of a passenger tire. The core of the study is an optimization design for improving the construction of the tire-building drum. The world-renowned TRIZ methodology was applied to achieve the desired improvement results. Using the TRIZ methodology, the technical system was analysed, identified problematic parts, and defined the technical and physical contradictions and proposed possibilities for their removal. The systematic approach to the solution of the task has generated options for the right solution and possible optimization by reducing the weight of individual parts of the tire-building drum. During analysis, simulations of the deformation and total stress will be available before and after optimization. The work’s conclusion describes the results of the simulation and the development process for the experimental testing possibilities of the optimized equipment. The study output is also a systematic procedure for testing the technical system, which can help designers design and optimize some parts of similar technical systems.
The rising demand for aluminium and environmental concerns highlight the need for a circular economy using recycled alloys. This study examines the effect of shot peening on the high-cycle fatigue life of secondary AlZn10Si8Mg alloys with different iron contents: Alloy A (0.14 wt.% Fe) and Alloy B (0.56 wt.% Fe). Although both alloys showed similar tensile properties, Alloy B had higher porosity and finer β-Al5FeSi intermetallics. Shot peening was applied at 100% and 1000% coverage to evaluate changes in surface roughness, porosity, residual stresses, and fatigue performance. The treatment significantly reduced surface-connected porosity via plastic deformation, enhancing fatigue life despite increased roughness. Fatigue tests showed a 21% increase in fatigue limit for Alloy A and a 6% gain for Alloy B at higher coverage. Fractographic analysis revealed that 95% of fatigue cracks initiated at surface pores. Residual stress measurements confirmed compressive stresses were limited to the near-surface layer, with minimal influence on subsurface crack propagation. Overall, shot peening proves to be an effective method for improving fatigue resistance in recycled aluminium alloys, even in alloys with elevated iron content, reinforcing their potential for structural applications under cyclic loading.