Lenka Kucharikova

Dr. Lenka Kucharikova

Department of Materials Engineering, Faculty of Mechanical Engineering, University of Zilina, 010 26 Žilina, Slovakia
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 July 2018 in Metals
Verified
Journal Article
Open access
PDF file
Lenka KucharikovaLenka Kucharikova
Lenka Kucharikova
TLTatiana Liptáková
Tatiana Liptáková
ETEva Tillová
Eva Tillová
DKDaniel Kajánek
Daniel Kajánek
ESEva Schmidova
Eva Schmidova
Aluminum alloys are the most important part of all shaped castings manufactured, especially in the aerospace and automotive industries. This work focuses on the corrosion properties of the heat-hardening aluminum alloys commonly used for production of automotive castings AlSi7Mg0.3 and on self-hardening AlZn10Si8Mg. Iron is a common impurity in aluminum cast alloy and its content increases by using secondary aluminum alloys. Therefore, experimental materials were developed, with chemical composition according to standards (primary alloys) and in states with an increasing content of Fe. The experimental aluminum alloys are briefly discussed in terms of their chemical composition, microstructure, mechanical properties and corrosion behavior. Corrosion properties were examined using three types of corrosion tests: exposure test, potentiodynamic tests, and Audi tests. Corrosion characteristics of materials were evaluated using stereo, optical and scanning electron microscopy, energy dispersive X-ray analysis, too. Correlation of pit initiation sites with microstructural features revealed the critical role of iron-rich phases, silicon particles and corresponding alloy matrix.

2 February 2017 in Transport Problems
Verified
Journal Article
Open access
Lenka KucharikovaLenka Kucharikova
Lenka Kucharikova
ETEva Tillová
Eva Tillová
OBOtakar Bokůvka
Otakar Bokůvka
Summary. Nowadays, a transportation industry creates a lot of metal scrap because production and use of cars are on the increase worldwide. This is based on the fact that increase in the production of cars increases usage of aluminium alloys in transportationapplications. Therefore, it is necessary to reduce the production of components

13 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
Lenka KucharikovaLenka Kucharikova
Lenka Kucharikova
Denisa StrakováDenisa Straková
Denisa Straková
ETEva Tillová
Eva Tillová
JBJuraj Belan
Juraj Belan
MKMichaela Kritikos
Michaela Kritikos
MUMilan Uhríčik
Milan Uhríčik
Secondary-cast aluminum alloys have increasing industrial applications. Their biggest deficiency is their impurity content, especially Fe, which has low solubility in Al and almost all the content creates intermetallic phases. This work examines the effect of higher Fe content on the microstructure and properties of A356.0 alloy. At the same time, no other possibility existed to affecting the brittleness of the formation of the β phases. The calculation of Fecrit, ratio of Mn/Fe, quantitative and computed tomography analysis of porosity and Fe plate-like phases, measurement of mechanical and fatigue properties, and fractography analysis were performed in this study. The results show that gravity die casting into a sand mold, and the non-usage of Mn addition or heat treatment, do not have a negative effect on increasing the size of the Fe-rich plate-like phases. The longest Fe-rich phases have limited the pore growth and ratios, but their higher thickness led to greater porosity formation. The mechanical and fatigue properties correlate with the Fecrit level and the highest were for the experimental alloy with 0.454 wt.% of Fe. The experimental results confirmed the fact that if the Fe plate-like phases have a length of up to 50 µm, the fatigue properties depend more on the size of porosity. If the length of the Fe needles is more than 50 µm, then the properties are mainly affected by the length of these Fe phases.

10 September 2019 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
JBJuraj Belan
Juraj Belan
Lenka KucharikovaLenka Kucharikova
Lenka Kucharikova
ETEva Tillová
Eva Tillová
MCMaria Chalupova
Maria Chalupova
A polycrystalline alpha-beta TiAl6V4 alloy in the annealed condition was used for the three-point bending fatigue test at frequencyf∼100 Hz. The static preloadFstat. = −15 kN and variable dynamic forceFdyn. = −7 kN to −13.5 kN were set as fatigue test loading parameters. The fatigue life S-N curve presented the stress amplitudeσaas a function of a number of cycles to fractureNf. A limiting number of cycles to run out of 2.0 × 107cycles were chosen for the 3-point fatigue tests of rectangular specimens. In addition, the Smith diagram was used to predict the fatigue life. The alpha lamellae width has a significant influence on fatigue life. It is assumed that the increasing width of alpha lamellae decreases fatigue life. A comparison of fatigue results with given alpha lamellae width in our material to the results of other researchers was performed. The SEM fractography was performed with an accent to reveal the initiation sites of crack at low and high load stresses and mechanism of crack propagation for the fatigue part of fracture.

30 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
VZViera Viera Zatkalíková
Viera Viera Zatkalíková
MUMilan Uhríčik
Milan Uhríčik
LMLenka Markovičová
Lenka Markovičová
Lenka KucharikovaLenka Kucharikova
Lenka Kucharikova
Corrosion resistance of sensitized austenitic stainless steel (SS) in chloride environments is currently the subject of numerous studies. Most of them are focused on neutral chloride solutions at room temperature and the experiments are carried out on ground stainless steels surfaces. This paper deals with the corrosion behavior of sensitized AISI 304 stainless steel in acid 1 M chloride solution (pH = 1.1) at the temperatures of 20 ± 3 °C and 50 °C. The specimens after sensitization are tested as covered by high-temperature surface oxides (“heat tinted”), and also after their chemical removal to assess the impact of the surface state on corrosion resistance. Potentiodynamic polarization (PP) and exposure immersion test are used as the independent corrosion tests. Microstructure before/after exposure immersion test is evaluated by optical microscopy (OM) and SEM. The results obtained showed that sensitization significantly conditions corrosion regardless of the removal of high-temperature oxides, and the elevated temperature mainly acts as its accelerating factor.

14 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
VZViera Viera Zatkalíková
Viera Viera Zatkalíková
SPStefan Podhorsky
Stefan Podhorsky
MŠMilan Štrbák
Milan Štrbák
TLTatiana Liptáková
Tatiana Liptáková
LMLenka Markovičová
Lenka Markovičová
Lenka KucharikovaLenka Kucharikova
Lenka Kucharikova
Plasma electrolytic polishing (PEP) is an environment-friendly alternative to the conventional electrochemical polishing (EP), giving optimal surface properties and improved corrosion resistance with minimum energy and time consumption, which leads to both economic and environmental benefits. This paper is focused on the corrosion behavior of PEP treated AISI 316L stainless steel widely used as a biomaterial. Corrosion resistance of plasma electrolytic polished surfaces without/with chemical pretreatment (acid cleaning) is evaluated and compared with original non-treated (as received) surfaces by three independent test methods: electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PP), and exposure immersion test. All corrosion tests are carried out in the 0.9 wt.% NaCl solution at a temperature of 37 ± 0.5 °C to simulate the internal environment of a human body. The quality of tested surfaces is also characterized by optical microscopy and by the surface roughness parameters. The results obtained indicated high corrosion resistance of PEP treated surfaces also without chemical pretreatment, which increases the ecological benefits of PEP technology.