Karol Chilmon

Dr. Karol Chilmon

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 April 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
HWHubert Witkowski
Hubert Witkowski
WJWioletta Jackiewicz-Rek
Wioletta Jackiewicz-Rek
Karol ChilmonKarol Chilmon
Karol Chilmon
JJJanusz Jaroslawski
Janusz Jaroslawski
ATAnna Tryfon-Bojarska
Anna Tryfon-Bojarska
AGArkadiusz Gąsiński
Arkadiusz Gąsiński
This paper presents the results of laboratory tests on photocatalytic pavement blocks from a bicycle lane in Poland after seven years of service. Air purification performance was tested on dusty and clean samples using different light sources and setups, with non-laminar gas circulation. Secondary Electrons Secondary Ions (SESI) and InLens detectors combined with SEM–EDS and X-ray analyses were applied to confirm the presence of TiO2 in the studied blocks. The obtained results show that TiO2 was present in the form of agglomerates with a diameter of 0.25–5 µm and was bonded to the cement matrix components. The tested samples still maintained nitric oxide (NO) removal capability with a NO reduction rate of 4–45%, depending on light source and surface cleanliness.

3 January 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
Maciej KalinowskiMaciej Kalinowski
Maciej Kalinowski
Karol ChilmonKarol Chilmon
Karol Chilmon
WJWioletta Jackiewicz-Rek
Wioletta Jackiewicz-Rek
BRBłażej Rakowski
Błażej Rakowski
This work aimed to investigate the influence of selected material variables on the self-cleaning and air purification efficiency in NOx pollutants of cement-based photocatalytic composites. Tests were performed on cement mortars, with seven independent variables considered: the mass ratio between cement and quartz powder to sand, the water to cement ratio, the total mass amount of photocatalysts (two different types), the mass content of nanoparticulate silica, the percentage of quartz powder replacing part of cement, and the ratio between two sands of fine granulation. Photocatalytic cementitious materials had their self-cleaning properties tested via two methods (spectrophotometry—the degradation of rhodamine B under UVA irradiation, and the change in the contact angle—via a goniometer). Air purification properties were tested in the reaction chamber under UVA and visible light at low irradiance (0.2 W/m2 for UVA, 150 W/m2 for visible). It was found that TiO2 content and the mass ratio between cement and quartz powder to sand were the most influential variables within the selected ranges of variability, with the ratio between sands and quartz content being the least significant variable of the tested properties.

17 January 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Katarzyna KoniecznaKatarzyna Konieczna
Katarzyna Konieczna
Karol ChilmonKarol Chilmon
Karol Chilmon
WJWioletta Jackiewicz-Rek
Wioletta Jackiewicz-Rek
The main assumption of eco-efficient High-Performance Concrete (HPC) design is the reduction of Portland cement clinker content without negatively affecting the composite’s mechanical and durability properties. In this paper, three low-clinker HPC mixtures incorporating slag cement (CEM III/B as per EN 197-1) and Supplementary Cementitious Materials (SCMs)—Ground Granulated Blast Furnace Slag (GGBFS), Siliceous Fly Ash (SFA) and Silica Fume (SF)—were designed. The maximum amount of Portland cement clinker from CEM III/B varied from 64 to 116 kg in 1 m3 of concrete mix. The compressive strength of HPC at 2, 7, 14, 28, 56, 90 days, and 2 years after casting, as well as the modulus of elasticity on 2-year-old specimens, was tested. The depth of water penetration under pressure and internal frost resistance in freeze–thaw tests were evaluated after 56 days of curing. Additionally, the concrete pH value tests were performed. The microstructure of 2-year-old HPC specimens was analyzed using Scanning Electron Microscopy (SEM). The research proved that it is possible to obtain low-clinker High-Performance Concretes that reach compressive strength of 76–92 MPa after 28 days of curing, show high values of modulus of elasticity (49–52 GPa) as well as increased resistance to frost and water penetration under pressure.

26 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
HWHubert Witkowski
Hubert Witkowski
WJWioletta Jackiewicz-Rek
Wioletta Jackiewicz-Rek
JJJanusz Jaroslawski
Janusz Jaroslawski
Karol ChilmonKarol Chilmon
Karol Chilmon
ASArtur Szkop
Artur Szkop
The application of photocatalytic materials has been intensively researched in recent decades. The process of nitric oxide (NO) oxidation during photocatalysis has been observed to result in the formation of nitric dioxide (NO2). This is a significant factor of the photocatalysis process, as NO2 is more toxic than NO. However, it has been reported that ozone (O3) is also formed during the photocatalytic reaction. This study analyzed the formation and oxidationof O3 during the photocatalytic oxidation of NO under ultraviolet irradiation using commercial photocatalytic powders: AEROXIDE® TiO2 P25 by Evonik, KRONOClean® 7050 by KRONOS®, and KRONOClean® 7000 by KRONOS®. An NO concentration of 100 ppb was assumed in laboratory tests based on the average nitric oxide concentrations recorded by the monitoring station in Warsaw. A mix flow-type reactor was applied in the study, and the appropriateness of its application was verified using a numerical model. The developed model assumed an empty reactor without a photocatalytic material, as well as a reactor with a photocatalytic material at its bottom to verify the gas flow in the chamber. The analysis of the air purification performance of photocatalytic powders indicated a significant reduction of NO and NOx and typical NO2 formation. However, no significant formation of O3 was observed. This observation was verified by the oxidation of pure ozone in the process of photocatalysis. The results indicated the oxidation of ozone concentration during the photocatalytic reaction, but self-decomposition of a significant amount of the gas.

30 October 2024 in Materials
Verified
Journal Article
Open access
PDF file
Maciej KalinowskiMaciej Kalinowski
Maciej Kalinowski
Karol ChilmonKarol Chilmon
Karol Chilmon
Jan BogackiJan Bogacki
Jan Bogacki
PWPiotr Paweł Woyciechowski
Piotr Paweł Woyciechowski
This research investigated the properties of modified cementitious composites including water purification from heavy metal—zinc. A new method for characterizing the immobilization properties of tested modifiers was established. Several additions had their properties investigated: biochar (BC), active carbon (AC), nanoparticulate silica (NS), copper slag (CS), iron slag (EAFIS), crushed hazelnut shells (CHS), and lightweight sintered fly ash aggregate (LSFAA). The impact of modifiers on the mechanical and rheological properties of cementitious composites was also studied. It was found that considered additions had a significantly different influence over the investigated properties. The addition of crushed hazelnut shells, although determined as an effective immobilization modifier, significantly deteriorated the mechanical performance of the composite as well as its rheological properties. Modification by iron slag allowed for a significant increase in immobilization properties (five-fold compared to the reference series) without a substantial impact on other properties. The negative effect on immobilization efficiency was observed for nanoparticulate silica modification due to its sealing effect on the pore network of the cement matrix. The capillary pore content in the cement matrix was identified as a parameter significantly influencing the immobilization potential of most considered modifications, except biochar and active carbon.

27 February 2025 in Coatings
Verified
Journal Article
Open access
PDF file
Maciej KalinowskiMaciej Kalinowski
Maciej Kalinowski
Karol ChilmonKarol Chilmon
Karol Chilmon
JKJustyna Kuziak
Justyna Kuziak
PŁPaweł Łukowski
Paweł Łukowski
WJWioletta Jackiewicz-Rek
Wioletta Jackiewicz-Rek
Photocatalytic coatings incorporating nano-TiO2 have emerged as effective solutions for air purification, utilizing solar radiation to degrade airborne pollutants. However, the long-term stability of such coatings, particularly those based on organic binders, remains a concern due to their susceptibility to photocatalytic-driven degradation. This study investigates the effects of low-intensity UV-A irradiation (1–10 W/m2) on acrylic-based photocatalytic coatings’ structural integrity and air purification performance. The findings reveal that significant binder decomposition occurs even under low irradiation conditions—comparable to natural sunlight exposure in Northern and Central Europe during autumn and winter. The surface porosity increased from 2.28% to 9.09% due to polymer degradation, exposing more nano-TiO2 particles and enhancing NO removal efficiency from approximately 120 µg/hm2 to 360 µg/hm2 under UV-A irradiation (1 W/m2). However, this process also resulted in benzene emissions reaching approximately five ppb, raising concerns about secondary pollution and the potential release of nano-TiO2 due to polymer matrix disintegration. These findings highlight the need for optimized coating formulations that balance photocatalytic efficiency with long-term material stability, mitigating the environmental and health risks associated with secondary pollutant emissions.