In this paper, a new technique for circular polarization in a slot coupled dielectric resonator antenna is proposed. The circular polarization is generated by inserting the two annular vias into dielectric resonator slightly off the diagonal position. In addition to the circular polarization, the proposed technique increases the total realized gain by 1.62 dB as compared to the via-less case on the account of increased directivity while maintaining the same aspect ratio of the DR. To validate the design, a prototype is fabricated and measured. The measured results show that the proposed circularly polarized dielectric resonator antenna has a −10 dB reflection bandwidth of 7.29% (3.3–3.55 GHz) and a 3 dB axial ratio bandwidth of 5.5% (3.28–3.465 GHz) with a measured RHCP gain of 6–7.1 dBic. The measured curves of the S 11 , axial ratio, and the RHCP gain results are in good agreement with the simulated results.
In this study, the mutual coupling in multiple-input-multiple-output (MIMO) dielectric resonator antenna (DRA) is reduced by employing closed metallic loops. The loops are wrapped around the adjacent edges of the dielectric resonators (DR) where magnetic coupling is significant. The proposed method employs only the conductive metallic strips for mutual coupling reduction and this makes the entire design very simple and compact. The impedance bandwidth varies from 4.73 to 5.1 GHz, covering the Sub–6 GHz 5G band. The realized MIMO DRA has an isolation of 28 dB at the resonant frequency with a measured peak gain at each port of 3.5 dBi and a peak radiation efficiency of 93%. The obtained measured results yield a low correlation coefficient (< 0.05) mostly at the entire band that contribute to diversity gain ( $ > 9.8$ dB) to increase the capacity of communication system, is reported in this paper. The proposed antenna was fabricated and the closed loop strip is wrapped around using in house facility. Furthermore, some issues related to the fabrications tolerance have been investigated to justify the difference between some simulated and measured results.
In this article, a high gain and compact 4 × 4 circularly polarized microstrip patch antenna array is reported for the data transmission of the next-generation small satellite. The radiating element of the circularly polarized antenna array is realized by the conventional model of the patch with truncated corners. A compact two-stage sequential rotational phase feeding is adopted that broadens the operating bandwidth of the 4 × 4 array. A small stub is embedded in the sequential rotational feed, which results in better performance in terms of the S-parameters and sequential phases at the output ports than sequential rotational feed without open stub. A prototype of the array is fabricated and measured. Fulfilling the application requirements of the next-generation small satellites, the array has the left-handed circularly polarized gain of more than 12 dBic with the axial ratio level below 1.5 dB in the ±10 angular space with respect to the broadside direction for the whole bandwidth from 8.05 GHz to 8.25 GHz. Moreover, the left-handed circularly polarized gain varies from 15 to 15.5 dBic in the desired band. The radiation patterns are measured; both the co- and X-pol are validated.
15 May 2023 in IEEE Antennas and Wireless Propagation Letters
This study investigates the used of decoupling structure to improve isolation and bandwidth in a multiple-input-multiple-output (MIMO) dielectric resonator antenna (DRA). The MIMO antenna consists of two identical DRAs that are fed by the same rectangular slots to excite the fundamental mode (TE $_{111}$ ). Two annular vias are inserted in each DRA to realize circular polarization at this mode. Moreover, the annular vias create quasi-hybrid mode (HEM $_{11\delta }$ ) in the DRA. Vertical and Z-shaped strips are printed on the adjacent walls of DRAs for isolation purposes, in which the Z-shaped strips coupled with the annular vias to realize the circular polarization at the HEM $_{11\delta }$ mode. Thus, improved bandwidth and isolation are achieved without occupying additional space. A prototype was fabricated and measured, which showed an overlapping 3 dB ARBW of 13.8% (2.7–3.1 GHz) with an isolation of 20 dB across the bandwidth, keeping the inter-element spacing of 0.03 $\lambda _{0}$ . The measured radiation patterns were in agreement with simulated results in $\phi =0$$^\circ (xz-plane)$ and $\phi =90$$^\circ (yz-plane)$ planes, achieving a peak right-handed circularly polarized (RHCP) gain of 4.3 dBi for a single port.
A double-layer element consisting of a spider-shaped structure on the top layer and a pair of concave arms with a circular ring on the middle layer is proposed for the wideband reflectarray with low cross-polarization characteristics. The unit cell offers a linear and wider phase range of 800. Based on the proposed unit cell, an offset-fed reflectarray with an octagonal aperture comprising 6769 unit cells is constructed at 11.725 GHz. The reflectarray offers 1 dB and 3 dB gain bandwidths of 25.2% and 32.3%, respectively, with an operating frequency range of 10–13.85 GHz. A peak gain of 31.2 dBi with an aperture efficiency of 42% is achieved. The cross-polarization levels are less than the co-polarization by 40 dB over the entire operating band.
This work presents the design and analysis of newly developed reconfigurable, flexible, inexpensive, optically-controlled, and fully printable chipless Arabic alphabet-based radio frequency identification (RFID) tags. The etching of the metallic copper tag strip is performed on a flexible simple thin paper substrate (ϵr = 2.31) backed by a metallic ground plane. The analysis of investigated tags is performed in CST MWS in the frequency range of 1–12 GHz for the determination of the unique signature resonance characteristics of each tag in terms of its back-scattered horizontal and vertical mono-static radar cross section (RCS). The analysis reflects that each tag has its own unique electromagnetic signature (EMS) due to the changing current distribution of metallic resonator. This EMS of each tag could be used for the robust detection and recognition of all realized 28 Arabic alphabet tags. The study also discusses, for the first time, the effect of the change in font type and size of realized tags on their EMS. The robustness and reliability of the obtained EMS of letter tags is confirmed by comparing the RCS results for selective letter tags using FDTD and MoM numerical methods, which shows very good agreement. The proposed tags could be used for smart internet of things (IoT) and product marketing applications.