Micro-LED (light-emitting diode) is a potentially disruptive display technology, while power consumption is a critical issue for all display devices. In this paper, we develop a physical model to evaluate the power consumption of micro-LED displays under different ambient lighting conditions. Both power efficiency and ambient reflectance are investigated in two types of full color display structures: red/green/blue (RGB) micro-LEDs, and blue-LED pumped quantum dots color-conversion. For each type of display with uniform RGB chip size, our simulation results indicate that there exists an optimal LED chip size, which leads to 30–40% power saving. We then extend our model to analyze different RGB chip sizes, and find that with optimized chip sizes an additional 12% average power saving can be achieved over that with uniform chip size.

We report a new nematic mixture for liquid-crystal-on-silicon spatial light modulator (SLM) and light detection and ranging (LiDAR) applications. The mixture exhibits a relatively high birefringence (Δn), moderate dielectric anisotropy (Δɛ), low viscosity, and reasonably good photostability. To achieve 2π phase change at 5 V, the response time (on + off) is 2.5 ms at 40 °C with λ = 633 nm, and 5.9 ms with λ = 905 nm. After exposure by a blue laser (λ = 465 nm) with a total dosage up to 20 MJ/cm², this mixture shows no sign of photodegradation. Widespread applications of this material for high brightness SLMs, LiDAR, near-eye displays, and head-up displays are foreseeable.

We evaluated and compared the performance of a 15.6-inch mini-LED backlit LCD (mLCD) with a commercial OLED (organic light-emitting diode) panel. Both displays exhibited outstanding properties, but the mLCD had advantages in peak brightness, gamma curve, luminance uniformity at low gray scales, color volume, power consumption, and ambient contrast ratio. In comparison with previous measurement methods, our color measurement adopted the reference method recently recommended by the International Committee for Display Metrology (ICDM). The LMK imaging photometer with a high-resolution CMOS sensor was employed to characterize the halo effect and reconstruct the real luminance profiles based on the non-ideal luminance profile of the OLED display. We also proposed a novel strategy to measure the point spread function of the backlight module.

Color-converted micro-light-emitting diode (micro-LED) displays with wide color gamut, high ambient contrast ratio, and fast response time are emerging as a potentially disruptive technology. However, due to limited optical density and thickness of the color-conversion film, the blue light leakage and low color-conversion efficiency still hinder their widespread applications. In this paper, we demonstrate a patterned cholesteric liquid crystal (CLC) polymer film with two special optical functionalities. On the green and red sub-pixels, the corresponding planar CLC texture acts as a distributed Bragg reflector for the blue light, which in turn improves the color conversion efficiency and expands the color gamut. On the blue sub-pixels, the corresponding focal-conic CLC texture acts as light scattering medium, which helps to reduce the angular color shift. Further analysis reveals that the patterned CLC film can alleviate the crosstalk between green and blue color filters. Therefore, compared to the display system without such a CLC film, our proposed device structure increases the color conversion efficiency by 143% (at ~90% Rec. 2020) and reduces average angular color shift Δu’v’ from 0.03 to 0.018 at the viewing angle with the most severe color shift. Such a patterned CLC film is applicable to all kinds of color-conversion display systems, including organic and inorganic phosphors.

We demonstrate a light efficient virtual reality (VR) near-eye display (NED) design based on a directional display panel and a diffractive deflection film (DDF). The DDF was essentially a high-efficiency Pancharatnam-Berry phase optical element made of liquid crystal polymer. The essence of this design is directing most of the display light into the eyebox. The proposed method is applicable for both catadioptric and dioptric VR lenses. A proof-of-concept experiment was conducted with off-the-shelf optical parts, where the light efficiency was enhanced by more than 2 times.

Vehicle displays are becoming more integrated into our daily lives. Achieving a premium driving experience demands the display panel to have high-resolution density and sufficient brightness, particularly when exposed to intense ambient light, as direct sunlight can obscure the displayed images. Combining Barten’s model and diffraction theory, the performance of both infotainment displays and head-up displays (HUDs) is evaluated. For infotainment displays, over 800 nit brightness is essential for the driver to discern 55 pixel-per-degree (PPD) patterns under direct sunlight. For HUDs, a delicate balance between resolution density, brightness, transparency, and image quality must be exercised. By slightly reducing the resolution density to 50 PPD, the transparent micro-LED panel can concurrently achieve a reduced background image blur, low required display brightness (~4000 nits), and high background transmittance (~90%).