Krzysztof Jackiewicz

Mr. Krzysztof Jackiewicz


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 September 2021 in Energies
Verified
Journal Article
Open access
PDF file
BBBogdan Bednarski
Bogdan Bednarski
KJKrzysztof Jackiewicz
Krzysztof Jackiewicz
AGAndrzej Galecki
Andrzej Galecki
Stepper motors are widely used in many applications where discrete, precise movement is required. There is a variety of dedicated stepper motor controllers (sometimes referred to as “step sticks”) available on the market. Those controllers provide a number of different motor control schemes that vary by aspects like current control method, reference current shape or maximum resolution increase (microstepping). The two most widely acknowledged signal shapes are sine-cosine microstepping and quadrature microstepping. The choice of the control scheme impacts torque output, torque variation, positioning error and maximum power supply requirements. This paper presents a family of generalised microstepping signal shapes, ranging from sine-cosine microstepping to quadrature microstepping. Derivation of signal shapes as well as their mathematical analyses are provided. Those signals are then implemented on the control board. A series of experiments is performed on a test bench to analyse the influence of different signal shapes on the performance of the motor in both load and no load conditions. The comparison of the new generalized shapes influence on the motor operation to the commonly used sine-cosine and quadrature control is provided.

9 June 2023 in ISA Transactions
Verified
Journal Article
Open access
MMMarek Michalczuk
Marek Michalczuk
AGAndrzej Galecki
Andrzej Galecki
BUBartlomiej Ufnalski
Bartlomiej Ufnalski
KJKrzysztof Jackiewicz
Krzysztof Jackiewicz
AKArkadiusz Kaszewski
Arkadiusz Kaszewski
The paper proposes a tuning procedure for a multioscillatory current controller in a three-phase three-wire grid connected converter operating under distorted voltage conditions. The control system should provide high quality sinusoidal currents. This is achieved by implementing internal models of expected disturbances - multioscillatory terms. Tuning of such systems is challenging if the objective is to guarantee a certain level of stability margins. The multiloop disk margin analysis may be a perfect candidate solution. This analysis combined with a global optimization produces controller gains that can be transferred to the physical system. The paper provides the first complete experimental verification of the multioscillatory full state feedback grid current control system with a designer specified stability margin in the form of disk radius.


1 September 2017
Verified
Conference Paper
Closed access
ABAdam Biernat
Adam Biernat
KJKrzysztof Jackiewicz
Krzysztof Jackiewicz
KBKrzysztof Bienkowski
Krzysztof Bienkowski

28 November 2025 in IEEE Access
Verified
Journal Article
Open access
ASAndrzej Straś
Andrzej Straś
MMMarek Michalczuk
Marek Michalczuk
KJKrzysztof Jackiewicz
Krzysztof Jackiewicz
TBTomasz Bałkowiec
Tomasz Bałkowiec
TSThomas Schüning
Thomas Schüning
Walter NeuWalter Neu
Walter Neu
The paper proposes a design procedure for a current control system of a permanent magnet linear synchronous machine for a small cargo transportation system. The drive system utilizes a long stator linear motor, and the vehicle is equipped with permanent magnets. Due to the possible high distance between the inverter and stator, the power circuit contains an LC filter. Therefore, the current controller must deal with a three-phase inductive–capacitive–inductive (LCL) circuit. Moreover, the stator of the machine is divided into segments. This leads to relatively fast changes in the induced voltage when the vehicle is passing through segment boundaries. Therefore, the current controller must deal with fast-changing disturbances. The state feedback control with gains selected using the linear-quadratic regulator approach is used to achieve high-quality system performance. Design and implementation include retuning of the controller gains for variable synchronous frequency. The control system is designed in the discrete domain concerning signal processing delay. The current control system with optimal gains is applied on the digital signal controller and verified experimentally on the test track.

1 June 2017
Verified
Conference Paper
Closed access
KBKrzysztof Bienkowski
Krzysztof Bienkowski
KJKrzysztof Jackiewicz
Krzysztof Jackiewicz
The results of four phase switched reluctance motor tests were presented in this paper. Torque versus speed characteristics were executed for different control parameters. The energy converter designed to this motor allows to control phase current and switching angles independently. The experimental results show that the shape of the mechanical characteristics heavily depends of the switching angles and maximum phase current. It has been found through tests, that efficiency characteristics of the drive can be improved by the right adjustment of the switching angles, even in the low load conditions.