The high-energy requirements of cleanrooms are the main motivation for optimizing their operational conditions. The ventilation system consumes the most energy in order to ensure the precise air conditioning of the room (filtration, temperature, and humidity adjustment). The main function of the ventilation system is to keep particle concentration to a minimum. This work deals with the optimization of an experimental operating room via the optimization of air supply through the distribution element (laminar airflow ceiling) in the range of 0.15–0.25 m·s−1. The laminar airflow between the distribution element and the patient is influenced by the operating light and different airflow velocities. These factors affect changes in particle concentration. Ansys Fluent software was used to investigate the nature of the flow, velocity profiles, and particle trajectories. The results of our numerical simulation demonstrate that a suitable flow rate setting increases the efficiency of particle reduction in the operating table area by up to 54%, which can, in turn, reduce operating costs. The simulated air velocity profile was subsequently verified using the particle image velocimetry (PIV) method. The typical size of particles monitored for in cleanrooms is 0.5 μm according to ISO EN 7. Therefore, the results of this study should be helpful in correctly designing distribution elements for clean rooms.
Forced ventilation is applied in clean rooms, specifically operating rooms, to ensure the health of both the patient and the medical staff. Ventilation reduces the risk of patient contamination, and its parameters are legally prescribed. In addition to preventing contamination, the ventilation system also ensures the creation of a comfortable environment for personnel who spend a large amount of working time in the operating room. This research focuses on the appropriate design of the air flow rate from the distribution element to the operating room. The PMV and PPD indexes were used to evaluate thermal comfort for human beings. The measurements of parameters determining thermal comfort took place in a laboratory with an accurate model of the operating room, including equipment and HVAC system, during the summer months, in cooling mode. Discharge speeds in the range of 0.15–0.175 m/s were evaluated as the most comfortable, with the PPD index ranging up to 22%. There was a significant increase in user dissatisfaction up to the limit of 70% at higher discharge speeds.
For countries with limited access to conventional hydrocarbon gases, methane hydrates have emerged as a potential energy source. In view of the European Union’s requirements to reduce the energy intensity of technological processes and increase energy security, it appears promising to accumulate natural gas and biomethane in the form of hydrate structures and release them if necessary. Storing gas in this form in an energy-efficient manner creates interest in developing and innovating technologies in this area. Hydrates that form in gas pipelines are generated by a more or less random process and are an undesirable phenomenon in gas transportation. In our case, the process implemented in the proposed experimental device is a controlled process, which can generate hydrates in orders of magnitude shorter times compared to the classical methods of generating natural gas hydrates in autoclaves by saturating water only. The recirculation of gas-saturated water has been shown to be the most significant factor in reducing the energy consumption of natural gas hydrate generation. Not only is the energy intensity of generation reduced, but also its generation time. In this paper, a circuit diagram for an experimental device for natural gas hydrate generation is shown with complete description, principle of operation, and measurement methodology. The natural gas hydrate formation process is analyzed using a mathematical model that correlates well with the measured hydrate formation times. Hydrates may become a current challenge in the future and, once verified, may find applications in various fields of technology or industry.
1 January 2026 in System Safety: Human - Technical Facility - Environment
The selection of filler metal for reparatory welding in this study is addressed through the application of the Square Root Based Evaluation Method (SREM). The aim of the paper was to examine the reliability of the method on a case that has already been solved using a Multi-Criteria Decision-Making (MCDM) approach in the relevant literature. Three filler metals, ABRADUR 58, E DUR 600, and CrWC 600, were considered and ranked based on four important criteria: wear trace width, cost, mass loss, and hardness of welded layers. All the experimental data, required for implementing the SREM method, were taken from a relevant literature source. The results of the study showed that E DUR 600 is the optimal filler metal. In addition, the results obtained using the SREM method are completely identical to those obtained using existing approaches, which confirms the applicability of this method to the considered problem. The sensitivity analysis showed that the ranking of filler metals may differ only in extreme cases, which indicates that the obtained results are sufficiently reliable.