Among thermophysical properties, the surface/interfacial tension, viscosity, and density/molar volume of liquid alloys are the key properties for the modelling of microstructural evolution during solidification. Therefore, only reliable input data can yield accurate predictions preventing the error propagation in numerical simulations of solidification related processes. To this aim, the thermophysical properties of the Fe-Si and Cu-Pb systems were analysed and the connections with the peculiarities of their mixing behaviours are highlighted. Due to experimental difficulties related to reactivity of metallic melts at high temperatures, the measured data are often unreliable or even lacking. The application of containerless processing techniques either leads to a significant improvement of the accuracy or makes the measurement possible at all. On the other side, accurate model predicted property values could be used to compensate for the missing data; otherwise, the experimental data are useful for the validation of theoretical models. The choice of models is particularly important for the surface, transport, and structural properties of liquid alloys representing the two limiting cases of mixing, i.e., ordered and phase separating alloy systems.
7 August 2019 in Metallography, Microstructure, and Analysis
By utilizing data from the literature, we examine the effects of superheat and solute additions on the grain size (as measured by columnar grain length) in binary copper alloys. Our investigation provides support for an Arrhenius-like behavior of the superheat on the grain size. We also find a correlation between the columnar grain length at a constant degree of superheat and the variation of the reciprocal of the true growth restriction factor (1/Q) with P, Mg, Mn, Pb, and Sn solute additions to be a power of law of 1/3, which gave a better fit than a linear one.
The effects of Si content (X = 4 to 7 wt.%), heating rate (5 to 25 °C/min) and sample mass (20 to 200 mg) on determination of the thixoforming working window by differential scanning calorimetry DSC were analyzed for the Al-Xwt.%Si-4wt.%Zn, or simply AlXSi4Zn, system. The critical lower and upper temperatures for thixoforming processing were determined by applying the differentiation method to DSC heating cycle data. Lower Si content, heating rate and DSC sample mass made identification of the working window temperatures more accurate because of the sharpening of the DSC curve when lower values of these variables were used. Data obtained when lower sample masses and heating rates were used agreed better with those obtained by Calculation of Phase Diagrams, (CALPHAD) simulation (near-equilibrium Scheil condition) for all the Si contents analyzed. Larger DSC sample masses were associated with significant heterogeneity in heat transfer through the sample, leading to results similar to those for a diffuse transition, an effect enhanced by an increase in the heating rate. Since Si content represented a limitation when identifying the working window by the differentiation method, alloys with high Si content should be analyzed with lower DSC masses and lower heating rates to allow more accurate determination of the interval at conditions near those used in thixoforming operations.
Among the thermophysical properties, the surface / interfacial tension, viscosity and density / molar volume of liquid alloys are the key properties for the modelling of microstructural evolution during solidification. Therefore, only reliable input data can yield accurate predictions preventing the error propagation in numerical simulations of solidification related processes. Due to experimental difficulties related to reactivity of metallic melts at high temperatures, the measured data are often unreliable or even lacking. The application of containerless processing techniques either leads to a significant improvement of the accuracy or makes the measurement possible at all. On the other side, accurate model predicted property values could be used to compensate the missing data; otherwise, the experimental data are useful for the validation of theoretical models. The choice of models is particularly important for the surface, transport and structural properties of liquid alloys representing the two limiting cases of mixing, i.e. ordered and phase separating alloy systems. To this aim, the thermophysical properties of the Fe-Si and Cu-Pb systems were analysed and the connections with the peculiarities of their mixing behaviours are highlighted.
6 November 2020 in Metallography, Microstructure, and Analysis
The effect of dilute solute additions on growth restriction in binary Cu alloys has been assessed at different degrees of superheat. Columnar grain length values from Northcott’s work (Northcott in J Inst Metals 62:101-136, 1938) for binary Cu alloys were plotted against the corresponding undercooling parameter (P), the reciprocal of the conventional (Qconv.) and true (Qtrue) growth restriction factor (Schmid-Fetzer and Kozlov in Acta Mater 59(15):6133-6144, 2011) values. It was found that there was no correlation between the columnar grain length values and P, 1/Qconv. and 1/Qtrue values for different solutes and cast at the same degree of superheat. Unlike P, Qconv., and Qtrue values, the heuristic growth restriction parameter (β) (Fan et al. in Acta Mater 152, 248-257, 2018) modeling framework in conjunction with the critical solute content (C*) for growth restriction fitted well to binary Cu alloys.
The effect of dilute solute additions on growth restriction in Cu-, Al-, Mg- and Ti-based binary and ternary alloys was assessed by means of the heuristic growth restriction parameter (β) modelling framework. The CALPHAD (calculation of phase diagrams) methodology was used to calculate β values from the m and k values, at first approximation, as well as from the liquid-to-solid fraction to obtain true β values. Grain size values from the literature were plotted against the corresponding true β values, showing a negative or inverse correlation between the two.