The development of novel strengthening techniques to address the seismic vulnerability of masonry elements is gradually leading to simpler, faster and more effective strengthening strategies. In particular, the use of fabric reinforced cementitious matrix systems is considered of great potential, given the increase of ductility achieved with simple and economic strengthening procedures. To assess the effectiveness of these strengthening systems, and considering that the seismic action is involved, one important component of the structural behaviour is the in-plane cyclic response. In this work is discussed the applicability of the diagonal tensile test for the assessment of the cyclic response of strengthened masonry. The results obtained allowed to assess the contribution of the strengthening system to the increase of the load carrying capacity of masonry elements, as well as to evaluate the damage evolution and the stiffness degradation mechanisms developing under cyclic loading.This research was carried in the framework of InoTec, Innovative material of ultra-high 16 ductility for the rehabilitation of the built patrimony, funded by COMPETE/QREN/FEDER 17 (NORTE-07-0202-FEDER-023024). InoTec project is promoted by CiviTest company 18 and University of Minho. S&P Clever Reinforcement Ibérica is gratefully acknowledged 19 for providing the materials used in the strengthening of the masonry specimens

In additive manufacturing (AM), one of the most popular procedures is material extrusion (MEX). The materials and manufacturing parameters used in this process have a significant impact on a printed product’s quality. The purpose of this work is to investigate the effects of infill percentage and filament orientation on the mechanical properties of printed structures. For this reason, the characterisation of polylactic acid (PLA) was done numerically using the finite element method and experimentally through mechanical tests. The experiments involved three-point bending and tensile tests. The results showed that mechanical performance is highly dependent on these processing parameters mainly when the infill percentage is less than 100%. The highest elastic modulus was exhibited for structures with filament align at 0° and 100% infill, while the lowest one was verified for specimen filament aligned at 0° and 30% infill. The results demonstrated that the process parameters have a significant impact on mechanical performance, particularly when the infill percentage is less than 100%. Structures with filament aligned at 0° and 100% infill showed the maximum elastic modulus, whereas specimens with filament oriented at 0° and 30% infill showed the lowest. The obtained numerical agreement indicated that an inverse method based only on the load–displacement curve can yield an accurate value for this material’s elastic modulus.

The behaviour of masonry elements under in-plane and out-of-plane loads can be improved through the application of strengthening systems based on reinforcing overlays. After strengthening, the transition region between the original substrate and the strengthening layer is especially stressed, and premature failure of the strengthened masonry is reached if insufficient interfacial capacity is assured. Therefore, the assessment of the mechanical behaviour of the interface is critical to the development of the masonry strengthening system based on the application of strengthening overlays. In this research a method for the characterization of the interface behaviour between two different materials, a polypropylene fibre reinforced mortar (PFRM) and a ceramic brick used for masonry construction is presented. Direct shear tests were carried out in couplet specimens. Due to the orthotropic nature of the bricks surface, the shear load was applied along three different directions in order to perform an overall estimation of the interface behaviour. The peak and residual shear stresses, as well as the failure modes, were obtained at different levels of the normal stress. Based on these experimental results constitutive laws were assessed for the simulation of the interface mechanical behaviour based on the Mohr and Mohr-Coulomb failure criteria.This research was carried in the framework of InoTec, Innovative material of ultra-high ductility for the rehabilitation of the built patrimony, funded by COMPETE/QREN/FEDER (NORTE-07-0202-FEDER-023024). InoTec project is promoted by CiviTest company and University of Minho. S&P Clever Reinforcement Ibérica is gratefully acknowledged for providing the materials used in the strengthening of the masonry specimen

The protection of the environment must be a priority in our society, and the construction sector can contribute significantly to this goal. Construction, being one of the industrial sectors that is more demanding in terms of raw materials, must reinforce its effort to implement, in a more profound and systematic way, the paradigm of the circular economy. In this sense, in recent years several studies have been trying to contribute solutions aimed at reintroducing industrial by-products or residues in new products for the construction industry. It should be noted that nowadays it is increasingly important to introduce a higher percentage of recycled materials in concrete. In this context, the present work addresses the appropriateness of a design procedure proposed to maximize the content of electric arc furnace slag (EAFS) and include recycled tire steel fibers (RTSF) in the production of more sustainable structural concretes. For this, the properties of various concrete mixtures at the fresh and hardened state, obtained by the substantial substitution of coarse and fine natural aggregates by EAFS and fly ash (FA), were investigated. The design of EAFS mixtures was based on two conventional reference mixtures (REF1 and REF2), and by using the modified Andreasen and Andersen particle packing model, these were optimized to achieve maximum packing density. Compressive strength, modulus of elasticity behavior, and fresh and physical properties were assessed in order to define the best mix proportions with respect to the predefined requirements of ordinary mixtures. Untreated recycled tire steel fibers (RTSF) were included in the developed sustainable concrete to perform a comparison of the physical properties with unreinforced concretes developed with natural aggregates (REF2) and with EAFS aggregates (EAFS8D1). This incorporation was intended to improve the physical behavior of unreinforced concretes with EAFS aggregates. Mixtures with high percentages of waste aggregates up to 70% (in weight), and 10% (in weight) of FA were obtained, showing competitive mechanical behavior compared to REF1 and REF2. These concrete compositions showed minimum and maximum compressive strengths between 9 MPa and 37 MPa, respectively. This study coverd the two major classes of concrete used as structural material, namely structural concrete and fiber reinforced concrete.