This work presents the results of research conducted with an aim to improve the surface quality, hardness and wear resistance of titanium alloy Ti6Al4V, obtained via the laser powder bed fusion of metals (PBF-LB/M) process of additive manufacturing (AM) known as the 3D printing of metals. The 3D surfaces were coated via reactive electrospark deposition (RESD) with low-pulse energy and electrode materials of low-melting metals and multi-component hard alloys. The relationship between the electrical parameters of the RESD process and the quality, composition, structure, microhardness and wear resistance of the treated surfaces were investigated and analysed. It was found that the roughness and thickness of the resulting surface layers could be changed by changing the RESD modes within the limits of 2.5–5 µm and 8–20 µm, respectively. RESD processing allowed us to achieve two to five times lower roughness than that of titanium AM surfaces. The microhardness and wear resistance of the RESD surfaces are two to four times higher than those of the titanium substrate. Possibilities for the purposeful synthesis of new wear-resistant phases and compounds and for obtaining surface layers with predetermined thickness and roughness were established. It was shown that the subsequent reaction’s electrospark processing helped to simultaneously reduce the roughness and increase the hardness and wear resistance of the modified surfaces, and can be successfully used instead of the material-energy-labour and machine-intensive finishing treatments of the titanium surfaces obtained after 3D printing.
In the present work, abrasive and erosive wear of wear-resistant composite coatings with a complex structure and different phase compositions deposited on titanium surfaces was studied. The coatings were obtained by electrospark deposition (ESD) using two types of hard-alloy compositions: WC–TiB2–B4C–Co–Ni–Cr–Si–B and TiB2–TiAl reinforced with dispersed nanoparticles of ZrO2 and NbC. The influence of the ESD process parameters on the roughness, thickness, composition, structure and coefficient of friction of the coated surfaces was investigated, and their role in protecting the titanium surfaces from wear was clarified. Dense coatings with the presence of newly formed wear-resistant phases and crystalline-amorphous structures were obtained, with roughness, thickness and microhardness that can be varied by the ESD modes in the range Ra = 2.5 ÷ 4.5 µm, δ = 8 ÷ 30 µm and HV 8.5 ÷ 14.0 GPa. The new coatings were found to reduce the abrasive and erosive wear of the coated surfaces by up to four times. The influence of the geometric characteristics, composition and structure of coatings on the wear intensity and wear resistance of coatings was studied.
Over the last two decades, the use of photovoltaic panels for the production of electricity has increased significantly, which leads to the need to solve the problems concerning the decommissioning and disposal of the panels and the development of appropriate technologies for their recycling. One of the key steps in this process is the separation of the tempered glass layer. Various technologies and devices are known for separating the glass of the solar panel by cutting it with a knife, as well as other instruments, with the different methods being based on mechanical, chemical, and thermal processes and accordingly having their own advantages and disadvantages. This article proposes an innovative approach for the mechanical delamination of solar panels using a metal wire heated by Joule heating, with the potential to become an energy-efficient, economical, and environmentally friendly method. This publication presents results from experiments using this type of tool to separate the layers of solar panels. Photos from a thermal camera are presented, showing the heat distribution in the panel and the reached operating temperature of the heated metal wire, necessary to soften the EVA bonding layer.
This work presents the results of deposition by magnetron sputtering nanostructured multilayer Cr/(Cr/a-C)ml coatings on AISI 316L and AISI 321 steel substrates. Chemical compositions were confirmed through EDX analysis with scanning electron microscopy. The coating thickness was measured with Calotester (KaloMAX II) and the total thickness of the coatings obtained ranged from 1.684 ± 0.193 μm for AISI 316L to 1.749 ± 0.123 μm for AISI 321. A Daimler-Benz Rockwell indentation test for adhesion quality and a nanoindentation test with a Berkovich indenter were carried out. According to the Raman spectroscopy analysis and in agreement with mechanical tests, it is supposed that it is the formation of a diamond-like carbon phase which enhances the mechanical properties. The hardness values obtained for the nanostructured multilayer Cr/(Cr/a-C)ml coatings were improved compared to those of the base stainless steels.
A chromium/amorphous carbon (Cr/(Cr/a-C)ml) nanostructured multilayer coating with a chromium sublayer was deposited on 42CrMo4 (1.7225,BDS EN ISO 683-2:2018), 100Cr6 (1.3505, BDS EN ISO 683-17:2024), and HS18-0-1 (1.3355, BDS EN ISO 4957:2018) alloy steels, selected for their use in contact-loaded components subjected to cyclic fatigue and intense wear. The coating was sputter deposited by MF pulsed magnetron sputtering under consistent process parameters. The resulting coating, approximately 1.8 μm thick, can significantly enhance the service life of these components. Adhesion was evaluated via the Daimler–Benz test, while coating homogeneity was confirmed through energy-dispersive spectroscopy, revealing a consistent chemical composition across sample surfaces. Raman spectroscopy indicated a high sp3/sp2 ratio, confirming a dominant diamond-like carbon structure. Nanoindentation measurements verified the coating’s hardness, aligning with the observed structural properties. These results validate the process parameters for depositing a Cr/(Cr/a-C)ml coating on these alloy steels, achieving this study’s objectives.
In the last two decades the use of photovoltaic panels for the production of electricity has increased significantly, which leads to the need to solve the problems related to the end-of-life disposal of the panels and the development of appropriate technologies for their recycling. One of the key steps in this process is the separation of the tempered glass layer. Various technologies and devices are known for separating the glass of the solar panel by cutting with a knife, as well as other instruments, with the different methods being based on mechanical, chemical and thermal processes and accordingly having their own advantages and disadvantages. This article proposes an innovative approach for mechanical delamination of solar panels using a metal wire heated by Joule heating, with the potential to become an energy-efficient, economical and environmentally friendly method. The publication presents results from experiments using this type of tool to separate the layers of solar panels. Photos from a thermal camera are presented, showing the heat distribution in the panel and the reached operating temperature of the heated metal wire, necessary to soften the EVA bonding layer.