To elucidate the key material parameters governing the tribological performance of ceramic composites under dry sliding against steel, this study presents a comprehensive comparative assessment of the microstructural characteristics, mechanical performance, and tribological behavior of two alumina–zirconia (Al₂O₃–ZrO₂) ceramic composites, each reinforced with a 42 vol.% carbide phase: zirconium carbide (ZrC) and tungsten carbide (WC). Specifically, tungsten carbide (WC) was selected for its exceptional bulk mechanical properties, while zirconium carbide (ZrC) was chosen to contrast its potentially different interfacial reactivity against a steel counterface. ZrC and WC were selected as reinforcing phases due to their high hardness and distinct chemical and interfacial properties, which were expected to critically affect the wear and friction behavior of the composites under demanding conditions. Specimens were consolidated via spark plasma sintering (SPS). The investigation encompassed macro- and nanoscale hardness measurements (Vickers hardness HV₁, HV₁₀; nanoindentation hardness H), elastic modulus (E), fracture toughness (K_IC), coefficient of friction (COF), and specific wear rate (W_s) under unlubricated reciprocating sliding against 100Cr6 steel at normal loads of 10 N and 25 N. The Al₂O₃–ZrO₂–WC composite exhibited an ultrafine-grained microstructure and markedly enhanced mechanical properties (HV₁₀ ≈ 20.9 GPa; H ≈ 33.6 GPa; K_IC ≈ 4.7 MPa·m^½) relative to the coarse-grained Al₂O₃–ZrO₂–ZrC counterpart (HV₁₀ ≈ 16.6 GPa; H ≈ 27.0 GPa; K_IC ≈ 3.2 MPa·m^½). Paradoxically, the ZrC-reinforced composite demonstrated superior tribological performance, with a low and load-independent specific wear rate (W_s ≈ 1.2 × 10⁻⁹ mm³/Nm) and a stable steady-state COF of approximately 0.46. Conversely, the WC-reinforced system exhibited significantly elevated wear volumes—particularly under the 25 N regime—and a higher, more fluctuating COF. Scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM–EDX) of the wear tracks revealed the formation of a continuous, iron-enriched tribofilm on the ZrC composite, derived from counterface material transfer, whereas the WC composite surface displayed only sparse tribofilm development. These findings underscore that, in steel-paired tribological applications of Al₂O₃–ZrO₂–based composites, the efficacy of interfacial tribolayer generation can supersede intrinsic bulk mechanical attributes as the dominant factor governing wear resistance.

Al₂O₃ with SiC, silver, and graphene nanoplatelets (GNPs) powder mixture was produced by ball milling using ethanol as dispersion media. The GNP-reinforced Al₂O₃-SiC-Ag ceramic–metal composites were densified by spark plasma sintering technology (SPS). A homogeneous dispersion of GNPs in Al₂O₃-SiC-Ag was observed from the sintered samples, and the GNPs were embedded between the grains, which resulted in increasing the contact area. The trans-granular mechanism of crack propagation becomes increasingly dominant by adding GNPs. The hardness reaches 27 GPa, as tested by the Vickers microhardness method, which reflects an increase of 11% compared to Ag-GNPs-free Al₂O₃-SiC. On the other hand, by adding Ag-GNP content, the improvement in density is limited. Wear mechanisms, as determined through ball-on-flat testing, including adhesion, abrasion, and microcracks, are observed and discussed. The composite demonstrated remarkable self-lubricating properties, exhibiting a lower coefficient of friction (COF) and wear rate in an air environment compared to monolithic Al₂O₃-SiC. This improvement is attributed to the formation of a self-lubricating film, enabled by the uniform distribution of Ag and GNPs within the Al₂O₃-SiC matrix. The findings of this study propose a novel material design approach for developing self-lubricating ceramic composites with hybrid solid lubricants.

This work systematically investigates the influence of two spark plasma sintering (SPS) temperatures (1400 °C and 1600 °C) on the mechanical and tribological properties of two yttria-stabilized zirconia ceramics: 3 mol.% Y₂O₃ (3Y-TZP) and 1.5 mol.% Y₂O₃ (1.5Y-TZP). The ceramics’ microhardness, nanohardness, Young’s modulus, fracture toughness, and tribological performance were evaluated. The results show that 3Y-TZP maintains high hardness (Vickers hardness HV ~1300; nanohardness ~17.1 GPa) and stable fracture toughness (~4.2 MPa·m½), nearly independently of sintering temperature. In contrast, 1.5Y-TZP exhibits a critical trade-off: sintering at 1400 °C yields exceptional fracture toughness (~6.2 MPa·m½), but increasing the temperature to 1600 °C causes a sharp drop to ~4.5 MPa·m½. Tribologically, the highest wear resistance under a 5 N load was observed for the 3Y-TZP sample sintered at 1600 °C. These findings suggest that for low-yttria compositions, higher SPS temperatures can trigger detrimental microstructural changes that degrade toughness. The results provide crucial insights for tailoring SPS parameters and Y-TZP compositions for specific high-performance applications, balancing the competing requirements of hardness and fracture toughness.

Non-oriented (NO) Fe–Si electrical steels are key materials for magnetic cores of electrical machines, requiring a balance between magnetic and mechanical properties. This study systematically examined the effect of silicon content (1.06 wt%, 2.15 wt%, and 3.09 wt%) on the microstructure, mechanical, and tribological behavior of three produced NO steel grades. Mechanical properties were assessed using tensile tests, microhardness, and nanoindentation, while tribological performance was evaluated under dry reciprocating sliding (ball-on-flat) against a 100Cr6 steel ball at loads of 5 N, 10 N, and 25 N. Increasing silicon content led to larger grain size, higher hardness (227 HV–361 HV) and strength, but lower ductility. Tribological behavior depended on both composition and load. The most stable friction regime occurred at 10 N. The medium-Si steel (N3, 2.15 wt%) exhibited the best performance with a low coefficient of friction (COF ≈ 0.52–0.55); N5 (3.09 wt%) showed a similar COF, while N1 (1.06 wt%) had a slightly higher value. At 25 N, an inverse relationship between hardness and friction appeared: softer N1 had the lowest COF (≈0.68–0.70), whereas harder N3 and N5 reached ≈ 0.74–0.78. Scanning electron microscopy (SEM) observations revealed abrasive wear for N3/N5 and plastic flow (galling) for N1. Overall, an optimal silicon content provides the best compromise between hardness and tribological stability depending on load conditions.

This study investigates the tribological behavior of composites based on Al ₂ O ₃ –ZrO ₂ stabilized with 3 mol. % Y ₂ O ₃ (ZTA – zirconia-toughened alumina), prepared using spark plasma sintering (SPS) technology. The composites were characterized in terms of microstructure, mechanical properties, and wear resistance in a dry ball-on-flat configuration. SEM analysis confirmed a homogeneous and fine-grained microstructure without porosity, with Al ₂ O ₃ grain sizes of 200–400 nm and ZrO₂ grain sizes of 100–200 nm. Measurements revealed high Vickers hardness (1566.7 ± 133.6 MPa), fracture toughness (6.4 ± 0.29 MPa·m¹ᐟ²), nanoindentation hardness (25.94 ± 2.35 GPa), and Young’s modulus (365.9 ± 18.2 GPa). The coefficient of friction ranged from 0.40 to 0.53 depending on the load, and the specific wear rate was extremely low (4.81 × 10⁻⁷ to 5.08 × 10⁻⁷ mm³/Nm). Analysis of the wear track revealed predominantly abrasive wear without significant fragmentation or delamination. The results demonstrate that optimized microstructure, proper phase stabilization, and a high degree of densification enable the preparation of composites with an excellent combination of hardness, toughness, and tribological resistance. These materials are suitable for demanding applications in industry, energy, and biomedicine.

This study investigates the mechanical and tribological behavior of three composites with a ZrO₂ matrix stabilized with 1.75 mol% Y₂O₃ and containing 1 wt.% Al₂O₃, reinforced with TiC (A), TiC + ZrC (B), and TiC + WC + Mo₂C (C). The matrix powder was synthesized by chemical coprecipitation, and the composites were consolidated by spark plasma sintering at 1350 °C. Dry reciprocating sliding tests against 100Cr6 steel were performed at 10 and 25 N. Composite A exhibited the highest HV10 hardness (1268), while the indentation fracture toughness values were similar (6.41–6.57 MPa·m^1/2). Wear resistance did not follow the hardness ranking. At 25 N, composite A exhibited surface fragmentation and a specific wear rate of 2.52 × 10⁻⁶ mm³·N⁻¹·m⁻¹, while composite B showed extensive and heterogeneous transfer of steel-derived material. Composite C exhibited the lowest coefficient of friction and specific wear rate, reaching 0.392 and 7.04 × 10⁻⁸ mm³·N⁻¹·m⁻¹, respectively, at 25 N. EDS mapping revealed an area-integrated Fe content of 0.7 at.% for C, compared with 7.2 at.% for A and B. The superior wear resistance of C was associated with substantially lower steel-derived material transfer and a relatively smooth wear-track surface rather than with the highest bulk hardness.