In this study, a highly sensitive, fast, and selective enzyme-free electrochemical sensor based on the deposition of Ni cavities on conductive glass was proposed for insulin detection. Considering the growing prevalence of diabetes mellitus, an electrochemical sensor for the determination of insulin was proposed for the effective diagnosis of the disease. Colloidal lithography enabled deposition of nanostructured layer (substrate) with homogeneous distribution of Ni cavities on the electrode surface with a large active surface area. The morphology and structure of conductive indium tin oxide glass modified with Ni cavities (Ni-c-ITO) were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The diameter of the resulting cavities was approximately 500 nm, while their depth was calculated at 190 ± 4 nm and 188 ± 18 nm using AFM and SEM, respectively. The insulin assay performance was evaluated by cyclic voltammetry. Ni-c-ITO exhibited excellent analytical characteristics, including high sensitivity (1.032 µA µmol⁻¹ dm³), a low detection limit (156 µmol dm⁻³), and a wide dynamic range (500 nmol dm⁻³ to 10 µmol dm⁻³). Finally, the determination of insulin in buffer with interferents and in real blood serum samples revealed high specificity and demonstrated the practical potential of the method.

Diamond-like carbon (DLC) coatings enhance tool wear resistance across various temperatures. The sp³/sp² bond ratio within DLC significantly impacts its properties and thermal stability. Elevated temperatures can alter DLC’s structure, while metallic elements and interlayers like chromium can modify its microstructure and performance. To evaluate the potential of W-DLC coatings with a chromium interlayer on 40CrMoV5-1 hot work tool steel under elevated temperatures, mechanical and tribological properties were assessed at room temperature and at temperatures of 100, 200, 300, 400, and 500 °C. Nanoindentation revealed a maximum hardness of 14.1 ± 1.3 GPa for the coating deposited at room temperature, attributed to a high sp³ content confirmed by Raman spectroscopy. Hardness decreased to 9.3 ± 1.0 GPa at 400 °C due to graphitization. The elastic modulus remained relatively constant across all temperatures. Tribological tests indicated a low coefficient of friction (CoF) of 0.15 at room temperature, increasing to 0.35 at 100 °C. The CoF further rose to 0.5 at 200 °C, coinciding with increased graphitization. However, the CoF reduced to 0.45 and 0.35 at 400 °C and 500 °C, respectively, likely due to the formation of a WO₃ tribo-film and the protective effect of the chromium interlayer.

In this work, solution-annealed AISI 316H grade austenitic stainless steel was studied in terms of investigating the electrolytic hydrogen charging effects on the resulting Charpy impact toughness and dry sliding tribological behavior. Conventional Charpy impact bending tests were employed to study the mechanical response of the investigated material to dynamic loading conditions, whereas dry linear sliding tribological tests were used to study material friction and wear behavior. The obtained mechanical and tribological properties were correlated with corresponding fracture and tribological mechanisms, which were determined from morphological observations of fracture surfaces and tribological tracks. The applied testing procedures were individually carried out for the non-hydrogenated, hydrogen-charged, and dehydrogenated material conditions. The observed changes in individual properties due to applied hydrogen charging were rather small, which indicated the good resistance of solution-annealed AISI 316H steel against material degradation in currently used electrolytic hydrogenation conditions.

This contribution describes the preparation, coupled with detailed characterization, of Nb₂O₅ nanofibers and their application in lithium–sulfur batteries for the improvement of electrochemical performance. The utilization of reactive needle-less electrospinning allowed us to obtain, in a single step, amorphous pre-ceramic composite PAN/Nb₂O₅ fibers, which were transformed into porous ceramic Nb₂O₅ nanofibers via calcination. Thermogravimetric studies defined that calcination at 600 °C results in crystalline ceramic fibers without carbon residues. The fibrous morphology and mean diameter (614 ± 100 nm) of the ceramic nanofibers were analyzed via scanning and transmission electron microscopy. A surface area of 7.472 m²/g was determined through nitrogen adsorption measurements, while a combination of X-ray diffraction and Raman spectroscopy was used to show the crystallinity and composition of the fibers after calcination—single T-phase Nb₂O₅. Its performance in the cathode of lithium–sulfur batteries was defined through electrochemical tests, and the obtained results were compared to a similar blank electrode. The initial discharge capacity of 0.5 C reached a value of 570 mAh∙g⁻¹, while the reversible capacity of 406 mAh∙g⁻¹ was retained after 200 cycles, representing a capacity retention of 71.3%. The presence of Nb₂O₅ nanofibers in the carbon cathode inhibits the shuttle effect through polysulphide confinement, which originates from porosity and chemical trapping.