3D integration photonic interposer is becoming popular in the field of co-packaging optics (CPO). In this paper, we integrate the edge coupler and through silicon via (TSV) into the silicon interposer. Different high-frequency transmission lines are designed, analyzed and simulated. The measured results and the simulation have a good correspondence. The high frequency transmission lines, which consist of 10 μm × 100 μm TSVs and two redistribution layer (RDL) lines of 100 μm on the top layer and one 100 μm RDL line on the bottom layer, shows perfect insertion loss less than 0.35 dB @67 GHz. In addition, the 56GBaud (112Gbps) eye diagram is tested and shows excellent transmission quality. Edge couplers are designed and fabricated by packaging process. The coupling loss of coupler is less than 1.7 dB/facet. The 3D optical package module based on the active optical interposer has also been realized and verified.
Recently, the interconnection bandwidth of the data center is rapidly increasing. To satisfy the requirement for the high-performance data center, a 4-channel 2.5D silicon photonic transmitter is proposed and the packaging structure could increase the high-density scalability of the architecture for 1.6T/3.2T co-packaging optics (CPO) module. The electrical driver and silicon photonic Mach-Zehnder modulator (MZM) are mounted to the silicon interposer by the micro-bumps. Meanwhile, the silicon interposer is mounted to the low temperature co-fired ceramic by the solder balls. The 2.5D transmitter is assembled to the motherboard by the high-speed ball grid array (BGA) connector to make it convenient to be replaced. The electrical optimization is implemented to make the insertion loss of the whole passive link within −1.55 dB under 40 GHz, which ensures the transmitter with the socket transmit the clear simulated eye diagram at 64 Gbps PAM4 rate per channel. Moreover, the thermal evaluation is performed, which includes the heat- dissipation evaluation and the thermal-induced impact on the edge light coupling. Finally, the substrates in the 2.5D transmitter are fabricated and the transmitter is realized by the improved assembly method. By the verification of the measurement, the 2.5D transmitter we proposed could work at 64 Gbps PAM4 signal transmission rate per channel with the 6pJ/bit power consumption. Regardless of the bandwidth of the electronic integrated circuit (EIC)/MZM and the BGA connector, based on the simulation electrical bandwidth, it is potential for realizing 100 Gbps PAM4 signal transmission.
This study explores the application of cold plate liquid cooling technology in co-packaged optics (CPO). By integrating optical modules and the switch chip on the same substrate, CPO shortens the electrical interconnection distance, effectively solving the problems of high power consumption and poor signal integrity of traditional pluggable optical modules under high bandwidth. However, the surge in power density and the thermal crosstalk resulting from high integration density make thermal management one of the key challenges that constrain the reliability of high-capacity co-packaged optics. For the unique architecture of CPO, this study analyzes its heat dissipation needs in detail, and a thermal management scheme is designed. The thermal management scheme is simulated and optimized based on the Navier−Stokes equation. The simulation results show that, in a 51.2 Tbit/s CPO system, the junction temperature of the switch chip is 97.3 °C, the maximum junction temperature of the optical modules is 31.3 °C, and the temperature difference between the optical modules is 2.4 °C to 1.2 °C. To verify the simulation results, a thermal test experimental platform is built, and the experimental results show that the temperature simulation difference is within 4% and the pressure change trend is consistent with the simulation. Combining the experimental data and simulation results, the designed heat sink can satisfy the heat dissipation demands of the 51.2 Tbit/s bandwidth CPO system. This conclusion demonstrates the potential of liquid-cooling technology in CPO, providing support for research on liquid-cooling technology in the CPO. The design provides a theoretical and practical basis for the high performance and reliability of optoelectronic integration technology in wavelength division multiplexing (WDM) systems and micro-ring device applications, contributing to the application of next-generation optical communication networks. Graphical Abstract
Recently, lumped Mach-Zehnder Modulators (MZMs) have received renewed attention due to their potential for low power consumption and compact size. However, the practicality of lumped MZMs with conventional lumped electrodes (C−LEs) is limited by their lower electro−optical (EO) bandwidth. The reduction in EO bandwidth results from the inherent trade−off between EO bandwidth and half−wave voltage length product () within the C−LE architecture. This paper proposes a thin−film lithium niobate (TFLN)−based lumped MZM with capacitively−loaded lumped electrodes (CL−LEs). The purely linear EO effect of the LN eliminates the parasitic capacitance in the doped PN junction and enhances the EO bandwidth. Furthermore, the CL−LE structure can break the limitation between EO bandwidth and inherent in the C−LE design. Simulations show the proposed device achieves a high EO bandwidth of 32.4 GHz and a low of 1.15 V·cm. Due to the reduced capacitance and lower , the power consumption of the device is as low as 0.1 pJ/bit. Simulation results indicate that the open−eye diagrams are achieved at 64 Gb/s for 1.5 mm TFLN lumped MZM, with an ER of 2.97 dB. Consequently, the proposed device architecture substantially enhances the performance of lumped MZMs, showing promise for application in short−reach optical interconnects within data centers.
16 August 2024 in IEEE Transactions on Components, Packaging and Manufacturing Technology
The development of semiconductors, driven by artificial intelligence (AI) and fifth-generation technology (5G) technologies, has posed challenges in advanced packaging. To address these challenges, a 3D packaging architecture based on active interposers has emerged. This paper presents novel fabrication method of active interposer with high-aspect-ratio through silicon vias (TSVs) and reliable assembly process of 3D chiplets. The proposed fabrication method of active interposer adopts frontside via-last TSV technology. Firstly, a two-step protection method etching is implemented to address low-dielectric constant (low-k) material over-etching risks. Then baking at 350 °C after TSV etching is suggested to prevent short circuits. Lastly, a blade saw followed by laser scribing is proposed to mitigate die chipping during the dicing saw of low-k material. Additionally, the 3D chiplet assembly process is optimized for low-thickness, large-area active interposer-to-substrate and high-density-I/O die-to-die bonding. Optimized recipe of thermal compression bonding (TCB), along with solder on pad (SoP), modified under-bump-metallization (UBM) and novel flux transfer method, ensures high-quality solder joints without voids or bridging. The validity of the optimized assembly process is confirmed by reliability tests. The successfully integrated 3D chiplets demonstrate that the fabrication process of active interposer and the optimized assembly flow can enhance the performance and reliability of 3D chiplet packaging in various applications.
3 July 2017 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Short-reach optical interconnection mainly focuses on the power consumption, the cost, and the volume. According to these requirements, the design and implementation of a multichannel transceiver are presented in this paper. In this paper, a high-coupling method without the 90° beam deflection is proposed so as to reduce the total power consumption to 0.9 W. Moreover, only the mature and low-cost packaging methods such as wire bonding and flip chip are adopted to satisfy the requirement of the optical coupling, which reduces the cost. Finally, the designed transceiver retains a small size of $28\times 16 \,\, \times $ 3 mm 3 . To ensure normal function of the transceiver, the organic substrate is carefully designed, and the post-design simulation is conducted to characterize the electrical performance. At last, the test results show that the optical transceiver with this novel packaging structure is able to transmit the data at 10 Gb/s per channel successfully.