films were grown on and layers by deposition of metallic Hf in an electron beam evaporation system followed by thermal oxidation. X-ray photoelectron spectroscopy confirmed the formation of stoichiometric films. There is no evidence of formation of hafnium silicide or carbon pileup at the surface as well as at the interfacial layer. Electrical measurements show the presence of fewer trapped charges in the gate dielectric stack compared to stack with a comparable interface state density. The stack layer improves leakage current characteristics with a higher breakdown field and has smaller flatband voltage shift under electrical stress, indicating improved reliability.
The stress of Cu/low- interconnects with linewidths scaled to 50 nm was determined using precision lattice parameter measurement at an advanced light facility. Grazing incidence and diffraction geometries were used to gain a direct measurement of the strain tensor, showing an increase in stress as the linewidth is reduced an order of magnitude from 500 to 50 nm. This increase in stress contrasts existing predictions of finite element simulations, which predict a decrease in stress as the line aspect ratio increases above one. Our simulations, considering the low- stack, have shown this decrease should occur at lower aspect ratios; however, neither trend is reflected in the measured data. All of the lines showed a strong [111] texture suggesting their stiffness was not affected at the scaled dimensions. The narrower lines show a more bamboolike structure compared to a more polycrystalline structure in the wider lines. In the narrow lines, the grains become pinned in the linewidth reducing stress relaxation through grain growth or reorder. This leads to the observed increase in stress with linewidth scaling and the increase in stress for bamboo lines during fabrication. This work demonstrates the grain structure of interconnects has a significant effect on stress and stress evolution.
27 August 2007 in IEEE Transactions on Device and Materials Reliability
This paper reports the first direct experimental measurement of electromigration-induced stress in aluminum interconnects, using a series of microrotating stress sensors. The build-up of stress gradients in interconnect metallization, which is concomitant with backstress, has been previously investigated theoretically, but experimental verification using optical or X-ray techniques has proven more difficult. These initial results show a compressive-stress gradient along the line of stress sensors, consistent with that predicted by conventional mass-transport theory. Additionally, these measurements are in qualitative agreement with the mathematical model proposed by Korhonen et al. (1993), with a reduced-stress and increased-diffusion coefficient. These differences are discussed, and the causes postulated. The limited resolution of previous techniques restricts their ability to obtain a detailed characterization, whereas, in principle, this new technique can be scaled to the end of the International Technology Roadmap for Semiconductors. These preliminary findings suggest that the presented technique will provide a valuable tool for the investigation of back-end-of-line interconnect stress in the future.
31 August 2020 in IEEE Transactions on Electron Devices
Germanium is commonly suggested as an alternative for power electronic devices in emerging liquid hydrogen applications. Despite the clear benefits of a twofold conductivity increase and fabrication familiarity within the community, very few models exist, which describe the temperature-dependent electrical characteristics of the material. Here, models are presented and adapted, which describe the temperature and doping dependence of the carrier concentration, mobility, and velocity from room temperature down to 20 K. For each of these, closed-loop models are adapted, which can be readily used in technology computer-aided design (TCAD) software, and new models are introduced when required. For high-field applications, the carrier velocity has been independently considered for both the 〈100〉 and 〈111〉 directions with the introduction of a new model for electrons in the 〈100〉 direction. With the work conducted here, it is now possible to simulate and predict the performance and suitability of germanium electronics for emerging low- and high-power applications.
Enhancement-mode 4H-SiC MOSFETs utilising an aluminium oxide (AlO) dielectric without the requirement for an underlying silicon oxide (SiO) layer have been shown to have a field effect mobility of 150 cmVs and a subthreshold swing of 160 mV/dec. The fabricated devices utilised a forming gas (3% H in N) anneal immediately prior to the deposition of the AlO by Atomic Layer Deposition (ALD). A comparison MOSFET using an identical AlO deposition process with a 0.7 nm SiO layer had a field effect mobility of approximately 20 cmVs. The hydrogen annealed device had a lower density of interface traps (), a lower subthreshold swing, and a significantly reduced hysteresis in the transconductance data than the thin SiO sample. This finding solves the issue of inconsistency of device performance using thin film gate dielectric as an interfacial layer by offering a simple and controllable process.
1 June 2021 in Materials Science in Semiconductor Processing