The aim of the study was to examine and compare oxidative stability of refined (peanut, corn, rice bran, grapeseed, and rapeseed) oils. The oils were subject a Schaal Oven Test (temperature 63 ± 1 °C) and a Rancimat test (temperature 120 °C) and their stability was compared at the 1st and 12th month of storage. Changes in the peroxide (PV) and anisidine (AnV) values in the thermostat test were the fastest in rapeseed oil and grapeseed oil. The best quality was preserved by peanut and corn oils both in the first and the twelfth month of storage. The induction times for the rice bran, corn, peanut, and rapeseed oils were similar from 4.77 h to 5.02 h in the first month and from 3.22 h to 3.77 h in the twelfth month. The shortest induction times were determined for grapeseed oil: 2.4 h and 1.6 h, respectively. A decrease of oxidative stability of about 30% was found in all the oils after 12 months of storage. The PV of 10, determined in the thermostat and Rancimat tests, were achieved at the latest in corn oil and the fastest in rice bran oil.

The aim of the study was to analyze the effect of the type of gelling substance on the selected physicochemical properties of oleogels. Rapeseed oil (RO) and 5% w/w of one of the following structuring compounds (SC) were used for their production waxes: sunflower (SUN), candelilla (CAN), bees white (BW), bees yellow (BY), or monoacylglycerols (MAG). The ability of SC to form a network in RO was assessed on the basis of an analysis of the texture of oleogels (hardness and spreadability test, stability determined by the centrifugal method). Oxidative stability was determined using the Rancimat test. In addition, the microstructure of an oleogel samples was observed at a magnification of 600 times in polarized light and in a bright field. Differences in the brightness and color of the samples were also assessed using the CIELab reflection method. The highest hardness (5.52 N) and physical stability (99.67%) were found in oleogel with candelilla wax. A higher value of the force causing deformation of the sample indicates a denser network of oil gel, which was confirmed by the microscopic images analyzed in the work. The organogel with CAN had the shortest (on average 8.49 nm) and the most regularly distributed crystals compared to other samples. The lowest values of organogel strength and spreadability test parameters (e.g., firmness, work of shear, stickness, work of adhesion), which were respectively 0.73 N, 4.39 N, and 9.74 N mm, while −4.87 N and −2.68 N mm were obtained with the variant, which was yellow beeswax. Considering the texture results obtained and the centrifugal stability, it was found that organogels with yellow beeswax were characterized by the worst structuring of rapeseed oil. Sunflower wax was considered the best among the analyzed gelling agents (under the conditions of the experiment). The organogel with its 5% w/w share was distinguished by the closest to the white color and texture most reminiscent of cream. In addition, it had the highest work of shear value and the longest induction time (6.8 h) in the Rancimat test.

The influence of the amount of inulin addition (3%, 6%, 9%, 12% or 15% w/w) on the physicochemical properties of natural yogurt was analyzed. The acidity (titration; pH), texture parameters (penetration test), viscosity curves (rotational rheometer), microrheology (macroscopic viscosity index, MVI; elasticity index, EI; solid-liquid balance—SLB; multi-speckle diffusing-wave spectroscopy, MS-DWS) and physical stability (syneresis; LUMiSizer test) of yogurts were investigated. All samples were non-Newtonian pseudoplastic liquids. The sample with 15% inulin content presented an approx. 4% higher pH value (4.34), 3-fold greater MVI and almost 5-fold higher penetration force, compared to the control sample (0% of inulin). In turn, the use of inulin addition in the range of 3–15% w/w resulted in a reduction of syneresis (p < 0.05). A linear decrease in the values of instability indexes and sedimentation velocities was noted in the function of inulin content increase (LUMiSizer test). The application of inulin (in the range of 3–15% w/w) as a functional additive to yogurts significantly contributed to enhancement of their physical stability. Summing up, the possibility of obtaining natural yogurts with a high content of this prebiotic has been demonstrated, thus such products can be classified as functional foods and a health claim can be put on the label.

The natural properties of oils and fats do not always allow for their direct use in industry (e.g., for food, cosmetics, and pharmaceuticals). Furthermore, such raw materials are often too expensive. Nowadays, the requirements for the quality and safety of fat products are increasing. For this reason, oils and fats are subjected to various modifications that make it possible to obtain a product with the desired characteristics and good quality that meets the needs of product buyers and technologists. The modification techniques of oils and fats change their physical (e.g., raise the melting point) and chemical properties (e.g., fatty acid composition). Conventional fat modification methods (hydrogenation, fractionation, and chemical interesterification) do not always meet the expectations of consumers, nutritionists, and technologists. In particular, Hydrogenation, while it allows us to obtain delicious products from the point of view of technology, is criticised for nutritional reasons. During the partial hydrogenation process, trans-isomers (TFA), dangerous for health, are formed. One of the modifications that meets current environmental requirements and trends in product safety and sustainable production is the enzymatic interesterification of fats. The unquestionable advantages of this process are the wide spectrum of possibilities for designing the product and its functional properties. After the interesterification process, the biologically active fatty acids in the fatty raw materials remain intact. However, this method is associated with high production costs. Oleogelation is a novel method of structuring liquid oils with small oil-gelling substances (even 1%). Based on the type of oleogelator, the methods of preparation can differ. Most oleogels of low molecular weight (waxes, monoglycerides, and sterols) and ethyl cellulose are prepared by dispersion in heated oil, while oleogels of high molecular weight require dehydration of the emulsion system or solvent exchange. This technique does not change the chemical composition of the oils, which allows them to keep their nutritional value. The properties of oleogels can be designed according to technological needs. Therefore, oleogelation is a future-proof solution that can reduce the consumption of TFA and saturated fatty acids while enriching the diet with unsaturated fatty acids. Oleogels can be named “fats of the future” as a new and healthy alternative for partially hydrogenated fats in foods.