Ivan Arregui

Ivan Arregui

Auto-generated profile, based on publicly available information

Ivan Arregui

Department of Electrical, Electronic, and Communications Engineering, Institute of Smart Cities (ISC), Public University of Navarre (UPNA), Campus Arrosadia, Pamplona, Spain

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 May 2024 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Open access
DSDavid Santiago
David Santiago
MFMu Fang
Mu Fang
AZAshraf Uz Zaman
Ashraf Uz Zaman
MLMiguel A.G. Laso
Miguel A.G. Laso
TLTxema Lopetegi
Txema Lopetegi
IAIvan Arregui
Ivan Arregui
This letter proposes a new design approach for filtering antennas. The novel matching reflection coefficient based method allows the integration of filters and antennas without compromising the frequency behavior of either of these components. Moreover, this integration is done avoiding the need of lengthy optimization processes and provides a high degree of flexibility in the types of antennas that can be used. In order to validate it, two examples are provided. In both cases, a 4 th -order Chebyshev bandpass filter at 101.5 GHz implemented in stacked groove gap waveguide (GGW) configuration is used, firstly along with a single aperture antenna and, subsequently, with a slotted ridge gap waveguide (RGW) array. This second example has been manufactured to demonstrate the usefulness of the new design methodology. Excellent measured performance has been obtained for a filtering antenna at W-band for the first time.

17 August 2023 in IEEE Access
Verified
Journal Article
Open access
DSDavid Santiago
David Santiago
MLMiguel A. G. Laso
Miguel A. G. Laso
TLTxema Lopetegi
Txema Lopetegi
IAIvan Arregui
Ivan Arregui
In this paper, a groove gap waveguide (GGW) low-pass filter is proposed for the first time. Gap waveguide technology represents an interesting alternative as a low-loss, cost-effective, high-performance transmission line and packaging solution for microwave and millimeter-wave systems. This technology may exhibit a frequency behavior similar to rectangular waveguide but with some advantages such as the no need of electrical contact between the upper and lower plates of the GGW, making it an attractive alternative in the design of satellite devices at high frequencies. However, all the previous literature focused on band-pass filters, while design methods for GGW low-pass filters have not been reported. Furthermore, in this paper a new manufacturing approach is proposed and its performance has been compared with traditional methods such as Computer Numerical Control (CNC) milling. The new approach relies on the Selective Laser Melting (SLM)-3D printing of the filter followed by a post-processing step, in which it is partially mechanized using CNC milling to improve the surface finish. Measurements of the manufactured prototypes are also included to compare both techniques at millimeter-waves, showing the advantages of the new fabrication method and the excellent agreement with the simulations.

1 June 2017
Verified
Conference Paper
Closed access
FTFernando Teberio
Fernando Teberio
Pablo Soto PachecoPablo Soto Pacheco
Pablo Soto Pacheco
IAIvan Arregui
Ivan Arregui
TLTxema Lopetegi
Txema Lopetegi
SCSantiago Cogollos
Santiago Cogollos
MLMiguel A. G. Laso
Miguel A. G. Laso
A rectangular waveguide band-pass filter with very low sensitivity to fabrication tolerances is proposed. The novel filter exploits the inherent first passband replica of commensurate-line stepped-impedance low-pass filters. Waveguide width reduction is also exploited to obtain a band-pass filter with a significant enhancement in the fabrication yield. This improvement is especially attractive for space applications in the millimeter-wave range. The validity of the novel design technique has been demonstrated with a 13 th -order Chebyshev band-pass filter for Q-band payloads. The manufacturing yield of the novel filter has been dramatically improved when compared to the classical inductive-iris filter designed to fulfill the same frequency specifications (92 % vs. 8 %, for a worst-case fabrication error of ± 25 μm). A prototype has been fabricated using milling techniques showing a very good agreement between simulated and measured results.

25 June 2018 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
FTFernando Teberio
Fernando Teberio
JPJon M. Percaz
Jon M. Percaz
IAIvan Arregui
Ivan Arregui
PMPetronilo Martin-Iglesias
Petronilo Martin-Iglesias
TLTxema Lopetegi
Txema Lopetegi
Israel ArnedoIsrael Arnedo
Israel Arnedo
In this paper, a new topology for rectangular waveguide bandpass and low-pass filters is presented. A simple, accurate, and robust design technique for these novel meandered waveguide filters is provided. The proposed filters employ a concatenation of ± 90° E-plane mitered bends (± 90° EMBs) with different heights and lengths, whose dimensions are consecutively and independently calculated. Each ± 90° EMB satisfies a local target reflection coefficient along the device so that they can be calculated separately. The novel structures allow drastically reduce the total length of the filters and embed bends if desired, or even to provide routing capabilities. Furthermore, the new meandered topology allows the introduction of transmission zeros above the passband of the low-pass filter, which can be controlled by the free parameters of the ± 90° EMBs. A bandpass and a low-pass filter with meandered topology have been designed following the proposed novel technique. Measurements of the manufactured prototypes are also included to validate the novel topology and design technique, achieving excellent agreement with the simulation results.

7 August 2019 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
JPJon M. Percaz
Jon M. Percaz
Israel ArnedoIsrael Arnedo
Israel Arnedo
IAIvan Arregui
Ivan Arregui
FTFernando Teberio
Fernando Teberio
PMPetronilo Martin-Iglesias
Petronilo Martin-Iglesias
TLTxema Lopetegi
Txema Lopetegi
In this paper, a novel and general method to synthetize microwave waveguide tapers intended for single-mode operation is proposed. The technique is based on the use of an exact series solution of the inverse scattering synthesis problem. An additional strategy necessary for dealing with waveguides where the propagation constant varies with the position is included. The coupled-mode theory is employed to model the electromagnetic behavior of the taper with the inherent mismatch caused by the connection of the waveguides with different cross sections. The novel method allows us to synthesize the (classical) transmission line taper functions of Klopfenstein and Hecken, making them suitable for general waveguide tapers with single-mode operation. Additionally, a new type of taper functions, also suitable for general waveguide tapers, is presented. The novel functions are obtained by partially employing the frequency response of multisection transformers, resulting in fully smooth tapers that can offer shorter lengths than the classical proposals. The taper synthesis procedure is demonstrated in rectangular waveguide technology, by requiring realistic and challenging specifications for different cases with different waveguide cross sections to be matched: height mismatch, width mismatch, and simultaneous height and width mismatch. Several prototypes of Klopfenstein, Hecken, and novel function tapers have been fabricated in an aluminum alloy by means of an Additive Manufacturing technique (Direct Metal Laser Sintering). The simulation and measurement results obtained for the rectangular waveguide taper prototypes confirm the accuracy of the novel synthesis technique proposed.

1 May 2015
Verified
Conference Paper
Closed access
FTF. Teberio
F. Teberio
IAI. Arregui
I. Arregui
AGA. Gomez-Torrent
A. Gomez-Torrent
EME. Menargues
E. Menargues
IAI. Arnedo
I. Arnedo
MLM. A. G. Laso
M. A. G. Laso
A lower-loss, more compact alternative to the classical E-plane corrugated waveguide low-pass filter is proposed in this paper. The novel design is capable of achieving very steep slopes in the fundamental TE 10 -mode frequency response along with a drastic reduction in terms of insertion loss and size. The design method is based on step-shaped bandstop elements separated by very short waveguide sections. Moreover, the matching of the novel filter is achieved by very short input/output networks based on stubs of optimized heights. A simple method is proposed allowing the designer to obtain a compact low-pass filter fulfilling stringent specifications.