Bipolar dc microgrid (MG) based on two voltage levels with three wires has higher reliability and flexibility than unipolar dc MG. However, the voltages of bipolar buses are coupled and the voltage of the PN bus affects the voltages of the bipolar buses in bipolar dc MG. In this article, a hierarchical control with voltage balancing and energy management based on the characteristics of bipolar dc MG is proposed. To perform distributed power sharing with coupled voltages, droop-based primary controls for three buses and the coupling relationships between three buses are analyzed. Furthermore, in secondary control, balancing and voltage restoration controls are proposed to compensate for voltage drops caused by the balanced and unbalanced loads. To design the proposed hierarchical control, the stability analysis is performed. Additionally, a tertiary control based on an artificial neural network is proposed for state-of-charge management of bipolar dc MG. Experimental results of the proposed hierarchical control are verified by a lab-scale bipolar dc MG and performance analysis is performed with experimental and ideal results.
13 December 2021 in IEEE Transactions on Power Electronics
To reduce the conducted common-mode (CM) electromagnetic interference (EMI) and current total harmonic distortion (THD) in permanent magnet synchronous motor drive systems, this article proposes a finite control set–model predictive control (FCS–MPC) method for an H8 inverter considering the dead-time (DT) effect. In a real system, the DT causes unexpected peak common-mode voltages (CMVs) and distortion of the inverter output voltage, which deteriorates both the CM EMI and current THD. The conventional double active voltage vector (VV) based MPC methods with an H6 inverter may not be a good solution because of the numerous CMV variations and the limit of the VV transitions. In contrast, the proposed FCS–MPC method allows all VV transitions possible without the peak CMVs by instantly operating the series-connected switch of the H8 inverter based on the previous VV, predicted current sector, and next optimal VV. Furthermore, the nonlinearity of the inverter output voltage due to the DT is compensated in a discrete-time model used for the current prediction, considering the calculation delay of the digital controller. Consequently, the current THD as well as the CM EMI can be improved. The simulation and experimental results are presented to verify the effectiveness of the proposed method.
This paper proposes a space vector modulation (SVM)-based common-mode (CM) currents reduction method of an H8 inverter for permanent magnet synchronous motor (PMSM) drives. There are power quality issues in the PMSM drive systems, such as current distortions and CM electromagnetic interference (EMI) due to the fast-switching operation of the inverter. These issues are related to CM voltage (CMV) and CM current (CMC). Although several studies have been conducted to reduce the CMV and CMC, some CMV variations and CMCs are still generated in the real implementation. Unlike conventional methods, the proposed method selects the voltage vectors with similar CMV levels and arranges them considering the series-connected switch operation of the H8 inverter in a voltage vector modulation sequence. At a low modulation index (MI), the proposed method completely restricts the CMV variations into six times. At high MI, the proposed method synthesizes the reference voltage vector differently, depending on the position of the reference vector, to reduce both current distortions and CMCs. The validity of the proposed method is verified through simulations and experimental results.
A virtual impedance-based flying start considering transient characteristics for permanent magnet synchronous machine drive systems is proposed. The conventional flying start based on virtual resistance (VR) assumes that the load of the system is resistive. However, the maximum value of VR, which is determined by the machine parameter and sampling frequency, is sometimes small. In this case, the load of the system is non-resistive. This assumption error causes an estimated position error and degrades transient characteristics. In the proposed method, algebraic-type virtual inductance (VI) is added to the estimation current regulator of the flying start based on VR. This change improves the accuracy of the estimated rotor position and the transient characteristics. In addition, the discrete-time system model of the proposed flying start method is given, the stability was analyzed considering the change in VR caused by the proposed method, and the improvements were verified by PSIM simulations and experimental results.
9 March 2021 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This study proposes an adaptive synchronous rectifier (SR) control scheme for high power density and high-efficiency interleaved boost converter (IBC) with passive soft-switching cell (PSC) (IBC-PSC). The PSC designed for the IBCs is one of the good solutions to minimize switching losses. However, the PSC needs a large boost inductance; otherwise, the conduction loss dramatically increases as the load decrease due to large circulating currents. Finally, there is a tradeoff between power density and efficiency. The proposed control scheme provides adaptive gating signals for the SR switches. It deactivates the SR switches at zero SR current and makes the main switches turn on with zero-voltage-switching (ZVS) regardless of the input voltage and load conditions, which results in reducing the conduction and switching losses despite significantly smaller boost inductance compared to the traditional IBC-PSCs. As a result, IBC-PSC with high power density and high efficiency can be realized. Theoretical analysis, implementation, and design considerations for the proposed control scheme were discussed and verified experimentally.
This paper proposes a novel dual integrated LLC resonant converter (DI-LRC) with a wide output voltage range using various switching patterns. The primary side of the proposed DI-LLC converter consists of two resonant tanks and six switches, while the secondary side consists of a six-pulse diode rectifier. Depending on the switching pattern of the primary switch, the DI-LRC converter is performed by single full-bridge operation with a voltage gain of 1, series-connected full-bridge operation with a voltage gain of 0.5, series-connected half bridge operation with a voltage gain of 0.25, and parallel-connected full-bridge operation with a voltage gain of 2. Accordingly, the proposed DI-LRC converter has four voltage gain curves with different variations and achieves a wider output voltage range than the conventional single voltage gain curve in a given operating frequency range. In this paper, the equivalent circuits derived for each switching pattern are proposed to analyze the operating characteristics of the proposed converter according to each switching pattern, and each Q factor and voltage gain are calculated based on the analyzed equivalent circuit. The performance of the proposed converter and switching pattern is verified using the simulation and experimental results of the prototype battery charger, which is designed to be 4-kW class.