This paper presents a DC-DC boost converter for energy harvesting. The time-domain maximum power point tracking (MPPT) technique implements to maximize the source's energy harvesting performance with no additional switch and time slot. Furthermore, it is implementing digital self-tracking zero current detectors (ST-ZCD) for high efficiency. This DC-DC boost converter fabricates with a 180nm CMOS process. The input voltage of the boost converter ranges from 0.2 to 0.7V and generates the output voltage of 1.2V. The total area of this converter with the MPPT operation is 600 μm x 475 μm. The measured power conversion efficiency of this DC-DC boost converter is 85.5%.
This paper presents a fast-switching Transmit/Receive (T/R) Single-Pole-Double-Throw (SPDT) Radio Frequency (RF) switch. Thorough analyses have been conducted to choose the optimum number of stacks, transistor sizes, gate and body voltages, to satisfy the required specifications. This switch applies six stacks of series and shunt transistors as big as 3.9 mm/160 nm and 0.75 mm/160 nm, respectively. A negative charge pump and a voltage booster generate the negative and boosted control voltages to improve the harmonics and to keep Inter-Modulation Distortion (IMD) performance of the switch over 100 dBc. A Low Drop-Out (LDO) regulator limits the boosted voltage in Absolute Maximum Rating (AMR) conditions and improves the switch performance for Process, Voltage and Temperature (PVT) variations. To reduce the size, a dense custom-made capacitor consisting of different types of capacitors has been presented where they have been placed over each other in layout considering the Design Rule Checks (DRC) and applied in negative charge pump, voltage booster and LDO. This switch has been fabricated and tested in a 90 nm Silicon-on-Insulator (SOI) process. The second and third IMD for all specified blockers remain over 100 dBc and the switching time as fast as 150 ns has been achieved. The Insertion Loss (IL) and isolation at 2.7 GHz are −0.17 dB and −33 dB, respectively. This design consumes 145 uA from supply voltage range of 1.65 V to 1.95 V and occupies 440 × 472 µm2 of die area.
This paper proposes a high-gain low-noise current signal detection system for biosensors. When the biomaterial is attached to the biosensor, the current flowing through the bias voltage is changed so that the biomaterial can be sensed. A resistive feedback transimpedance amplifier (TIA) is used for the biosensor requiring a bias voltage. Current changes in the biosensor can be checked by plotting the current value of the biosensor in real time on the self-made graphical user interface (GUI). Even if the bias voltage changes, the input voltage of the analog to digital converter (ADC) does not change, so it is designed to plot the current of the biosensor accurately and stably. In particular, for multi-biosensors with an array structure, a method of automatically calibrating the current between biosensors by controlling the gate bias voltage of the biosensors is proposed. Input-referred noise is reduced using a high-gain TIA and chopper technique. The proposed circuit achieves 1.8 pArms input-referred noise with a gain of 160 dBΩ and is implemented in a TSMC 130 nm CMOS process. The chip area is 2.3 mm2, and the power consumption of the current sensing system is 12 mW.
4 April 2025 in IEEE Open Journal of Circuits and Systems
This paper presents a bidirectional Four-Switch Buck-Boost (FSBB) converter with a high-voltage (HV) gate driver for use in power bank applications. The proposed FSBB is also integrated into this converter for increased efficiency. Thus, the proposed buck-boost converter can reduce conduction loss over a wide input voltage range by reducing the on-resistance of external MOSFETs using a gate source voltage (VGS) of 5V or 10V. The chip to be examined in this study is fabricated using a 130 nm 1P5M bipolar-CMOS-DMOS HV process with laterally diffused MOSFET (LDMOS) options to have a die size of 2.7 x 2.7 mm2. The proposed architecture is found to achieve a maximum output power level of 40W. The measurement results show that the maximum efficiencies at gate-source voltages (VGS) of 5V and 10V are 96.67% and 98.15%, respectively.
This paper presents and discusses a Low-Band (LB) Low Noise Amplifier (LNA) design for a diversity receive module where the application is for multi-mode cellular handsets. The LB LNA covers the frequency range between 617 MHz to 960 MHz in 5 different frequency bands and a 5 Pole Single Throw (5PST) switch selects the different frequency bands where two of them are for the main and three for the auxiliary bands. The presented structure covers the gain modes from −12 to 18 dB with 6 dB gain steps where each gain mode has a different current consumption. In order to achieve the Noise Figure (NF) specifications in high gain modes, we have adopted a cascode Common-Source (CS) with inductive source degeneration structure for this design. To achieve the S11 parameters and current consumption specifications, the core and cascode transistors for high gain modes (18 dB, 12 dB, and 6 dB) and low gain modes (0 dB, −6 dB, and −12 dB) have been separated. Nevertheless, to keep the area low and keep the phase discontinuity within ±10, we have shared the degeneration and load inductors between two cores. To compensate the performance for Process, Voltage, and Temperature (PVT) variations, the structure applies a Low Drop-Out (LDO) regulator and a corner case voltage compensator. The design has been proceeded in a 65-nm RSB process design kit and the supply voltage is 1 V. For 18 dB and −12 dB gain modes as two examples, the NF, current consumption, and Input Third Order Intercept Point (IIP3) values are 1.2 dB and 16 dB, 10.8 mA and 1.2 mA, and −6 dBm and 8 dBm, respectively.
This paper presents a 5.8 GHz differential cascode power amplifier for an over-the-air wireless power transfer application. Over-the-air wireless power transfer provides a variety of benefits in several applications such as the Internet of Things and medical implantation applications. The proposed PA features two fully differentially active stages with a custom-designed transformer to provide a single-ended output. The custom-made transformer shows a high quality factor, as high as 11.6 and 11.2 for the primary and secondary sides at 5.8 GHz. Fabricated using a standard 180 nm CMOS process, the amplifier achieves input and output matching of −14.7 dB and −29.7 dB, respectively. To achieve a high power level and efficiency, accurate optimization through power matching, Power Added Efficiency (PAE), and the design of the transformer are carried out while the supply voltage is limited to 1.8 V. Measurement results show a 20 dBm output power with a PAE as high as 32.5%, which makes the PA suitable for application, and it can be implanted while arrayed with various antenna arrays. Finally, a FOM is introduced to compare the performance of the work with similar works in the literature.