This article presents a power-efficient hybrid energy-harvesting system that scavenges energy from solar, vibration, and radio frequency (RF) energy sources and converts into regulated output dc voltage courtesy buck–boost dc–dc converter. The proposed architecture incorporates tetra-paths for maintaining high power conversion efficiency (PCE) over extended input power range (−10 to 30 dBm). A time-domain maximum power point tracking technique is proposed for solar energy harvester. A high-efficiency full wave rectifier is designed for triboelectric rectifier. A 5.8-GHz RF-dc converter with adaptive matching is proposed to increase dynamic range of the input power. The chip is implemented in 0.18-µm bipolar-CMOS-DMOS process. The die area of the chip is 2.8 mm × 5.0 mm, including the pads. The solar and triboelectric energy harvesters achieve a measured peak efficiencies of 75.4% and 92.3%, respectively. The high-power 5.8-GHz RF-dc converter achieves measured PCE of 76% at 30 dBm input power. The low-power dual-band RF-dc converter operating at 900 MHz and 2.4 GHz obtains measured peak efficiencies of 73% and 71.9% at 0 dBm input, respectively. The buck–boost dc–dc converter employed in the proposed hybrid energy harvesting system achieves a measured peak PCE of 94.5%.
9 October 2018 in IEEE Transactions on Power Electronics
This paper presents a reconfigurable wide input power range radio frequency (RF) energy harvester (EH) with alliance for wireless power (A4WP) wireless power receiver (WPR). A reconfigurable RF-DC converter for RF EH and maximum power point tracking algorithm are proposed to maintain high efficiency over a wide input power range -20 to +20 dBm. The A4WP WPR is designed and merged with the EH to receive power higher than +20 dBm. In order to improve the power conversion efficiency (PCE), the delay between the ac input voltage and current is compensated by the proposed open-loop delay compensation method. The chip is implemented in 0.18 μm bipolar-CMOS-double-diffused metal-oxide-semiconductor process. The die area of the chip is 4.3 mm × 3.2 mm, including the pads. The proposed EH with WPR achieves a measured peak PCE of 48.19% with respect to the input power of 0 dBm at 900 MHz. It also has a peak PCE of 82.14% with respect to the input power of 30 dBm in an A4WP mode operation at 6.78 MHz.
Recently, piezoresistive-type (PRT) pressure sensors have been gaining attention in variety of applications due to their simplicity, low cost, miniature size and ruggedness. The electrical behavior of a pressure sensor is highly dependent on the temperature gradient which seriously degrades its reliability and reduces measurement accuracy. In this paper, polynomial-based adaptive digital temperature compensation is presented for automotive piezoresistive pressure sensor applications. The non-linear temperature dependency of a pressure sensor is accurately compensated for by incorporating opposite characteristics of the pressure sensor as a function of temperature. The compensation polynomial is fully implemented in a digital system and a scaling technique is introduced to enhance its accuracy. The resource sharing technique is adopted for minimizing controller area and power consumption. The negative temperature coefficient (NTC) instead of proportional to absolute temperature (PTAT) or complementary to absolute temperature (CTAT) is used as the temperature-sensing element since it offers the best temperature characteristics for grade 0 ambient temperature operating range according to the automotive electronics council (AEC) test qualification ACE-Q100. The shared structure approach uses an existing analog signal conditioning path, composed of a programmable gain amplifier (PGA) and an analog-to-digital converter (ADC). For improving the accuracy over wide range of temperature, a high-resolution sigma-delta ADC is integrated. The measured temperature compensation accuracy is within ±0.068% with full scale when temperature varies from −40 °C to 150 °C according to ACE-Q100. It takes 37 µs to compute the temperature compensation with a clock frequency of 10 MHz. The proposed technique is integrated in an automotive pressure sensor signal conditioning chip using a 180 nm complementary metal–oxide–semiconductor (CMOS) process.
21 February 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a low-power frequency-shift keying (FSK) transmitter (TX) with an all-digital phase locked loop (ADPLL) based on direct modulation for use in Bluetooth low energy application. A low power ADPLL with a Retimer, 2-stage time to digital converter, and gain estimation technique is proposed to achieve low-power direct FSK modulation at 1 Mbps data rate. A high-efficiency class-D power amplifier, with dual output power modes and a ramping digital filter (RDF), is proposed to reduce the spurious tones. The proposed TX is implemented on 1P6M 55-nm CMOS technology with a die size of 0.53 mm². The phase noise is -119 dBc/Hz at a 1 MHz offset with frequency of 2.44 GHz. TX output power levels of 1.6 and 10 dBm have a power consumption of 3.9 and 18 mW, respectively. The power control ranges for the 1.6 and 10 dBm modes are 25 and 23 dB, respectively. With the RDF, when the output level is +1.6 dBm, the second, and third harmonic distortions at the TX output are -44 and -49 dBm, respectively. The proposed TX achieves an error vector magnitude of 3.48% at an output power level of +1.6 dBm.
A design of low-power 10-bit 1 MS/s asynchronous successive approximation register analog-to-digital converter (SAR ADC) is presented in this paper. To improve the linearity of the digital-to-analog converter (DAC) and energy efficiency, a common mode-based monotonic charge recovery (CMMC) switching technique is proposed. The proposed switching technique consumes only 63.75 CVREF2 switching energy, which is far less as compared to the conventional switching technique without dividing or adding additional switches. In addition, bootstrap switching is implemented to ensure enhanced linearity. To reduce the power consumption from the comparator, a dynamic latch comparator with a self-comparator clock generation circuit is implemented. The proposed prototype of the SAR ADC is implemented in a 55 nm CMOS (complementary metal-oxide-semiconductor) process. The proposed architecture achieves a figure of merit (FOM) of 17.4 fJ/conversion, signal-to-noise distortion ratio (SNDR) of 60.39 dB, and an effective number of bits (ENOB) of 9.74 bits with a sampling rate of 1 MS/s at measurement levels. The implemented SAR ADC consumes 14.8 µW power at 1 V power supply.