A design of low-power 10-bit 1 MS/s asynchronous successive approximation register analog-to-digital converter (SAR ADC) is presented in this paper. To improve the linearity of the digital-to-analog converter (DAC) and energy efficiency, a common mode-based monotonic charge recovery (CMMC) switching technique is proposed. The proposed switching technique consumes only 63.75 CV_REF² switching energy, which is far less as compared to the conventional switching technique without dividing or adding additional switches. In addition, bootstrap switching is implemented to ensure enhanced linearity. To reduce the power consumption from the comparator, a dynamic latch comparator with a self-comparator clock generation circuit is implemented. The proposed prototype of the SAR ADC is implemented in a 55 nm CMOS (complementary metal-oxide-semiconductor) process. The proposed architecture achieves a figure of merit (FOM) of 17.4 fJ/conversion, signal-to-noise distortion ratio (SNDR) of 60.39 dB, and an effective number of bits (ENOB) of 9.74 bits with a sampling rate of 1 MS/s at measurement levels. The implemented SAR ADC consumes 14.8 µW power at 1 V power supply.

In this research work, a reconfigurable 2.45-GHz RF-DC converter realized in a 180-nm complementary metal-oxide semiconductor (CMOS) technology is proposed to efficiently harvest electromagnetic energy. The proposed circuit is composed of a low-power path rectifier, a high-power path rectifier, and an adaptive path control (APC) circuit. The APC circuit is made-up of a comparator, two switches, and an inverter. The APC circuit senses the output voltages of the low-power path and the high-power path rectifiers and generates a control signal to automatically switch the proposed circuit between the lower-power path and the high-power path operation depending upon RF input power level. The proposed circuit obtains more than 20% measured power conversion efficiency (PCE) from −6 dBm to 11 dBm input power range with maximum efficiencies of 41% and 45% at 1 and 6 dBm input powers, respectively, for 5 kΩ load resistance. In addition, the proposed circuit shows excellent performance at 900 MHz and 5.8 GHz frequencies.

A low power 12-bit, 20 MS/s asynchronously controlled successive approximation register (SAR) analog-to-digital converter (ADC) to be used in wireless access for vehicular environment (WAVE) intelligent transportation system (ITS) sensor based application is presented in this paper. To optimize the architecture with respect to power consumption and performance, several techniques are proposed. A switching method which employs the common mode charge recovery (CMCR) switching process is presented for capacitive digital-to-analog converter (CDAC) part to lower the switching energy. The switching technique proposed in our work consumes 56.3% less energy in comparison with conventional CMCR switching method. For high speed operation with low power consumption and to overcome the kick back issue in the comparator part, a mutated dynamic-latch comparator with cascode is implemented. In addition, to optimize the flexibility relating to the performance of logic part, an asynchronous topology is employed. The structure is fabricated in 65 nm CMOS process technology with an active area of 0.14 mm². With a sampling frequency of 20 MS/s, the proposed architecture attains signal-to-noise distortion ratio (SNDR) of 65.44 dB at Nyquist frequency while consuming only 472.2 µW with 1 V power supply.

This paper presents an energy-efficient low power 10-b 8-MS/s asynchronous successive approximation register (SAR) analog-to-digital (ADC) converter. An inverted common-mode charge recovery technique is proposed to reduce the switching energy and to improve the linearity of the digital-to-analog converter (DAC). The proposed switching technique consumes only 149 CV_REF² switching energy for the 10-bit case. A rail-to-rail dynamic latch comparator is implemented with adaptive power control for better power efficiency. Additionally, to optimize the power consumption and performance of the logic part, a modified asynchronous type SAR control logic with digitally controllable delay cells is adopted. An on-chip reference voltage generator is also designed with an ADC core for practical use. The structure is realized using 55-nm complementary metal–oxide–semiconductor (CMOS) process technology. The proposed architecture achieves an effective number of bits (ENOB) of 9.56 bits and a signal-to-noise and distortion ratio (SNDR) level of 59.3 dB with a sampling rate of 8 MS/s at measurement level. The whole architecture consumes only 572 µW power when a power supply of 1 V is applied.

This paper presents a second-order discrete-time Sigma-Delta (SD) Analog-to-Digital Converter (ADC) with over 80 dB Signal to Noise Ratio (SNR), which is applied in a signal conditioning IC for automotive piezo-resistive pressure sensors. To reduce the flicker noise of the structure, choppers are used in every stage of the high gain amplifiers. Besides, to reduce the required area and power, only the CIC filter structure is adopted as a decimation filter. This filter has a configurable structure that can be applied to different data rates and input signal bandwidths. The proposed ADC was fabricated and measured in a 0.18-µm CMOS process. Due to the application of only a CIC filter, the total active area of the SD-ADC and reference generator is 0.49 mm² where the area of the decimation filter is only 0.075 mm². For the input signal bandwidth of 1.22 kHz, it achieved over 80 dB SNR in a 2.5 MHz sampling frequency while consuming 646 µW power.

A 12-bit 80 MS/s hybrid type analog-to-digital converter (ADC) for high sampling speed and low power applications is presented in this paper. It has a subranging architecture with a front end of 6-bit Flash ADC with five channels of 6-bit time interleaved synchronous Successive Approximation Register (SAR) ADC. The proposed architecture with a shared 6-bit Flash ADC and time interleaved SAR ADC provides a power and area efficient high speed ADC. The proposed Time-skew calibration is implemented to minimize the discrepancy between the output of Flash ADC and SAR ADC’s channels. To rectify the decision error of the Flash ADC and extract the time-skew information, 1-bit redundancy is included in the CDAC of the SAR conversion. The decision error between the Flash ADC and the SAR ADC is covered with designed redundancy and the mismatch between the ADCs is covered with the time-skew calibration. To reduce the offset mismatch between Flash and SAR ADC and within SAR ADCs, all comparators are calibrated to minimize their absolute offset by utilizing background offset calibration. The modified dynamic strong ARM comparator is used for flash ADC and dynamic latched comparator is used for SAR ADCs. For fine offset calibration and low power consumption, the comparator’s offset calibration circuit is implemented. To reduce the kickback noise and enhance the overall energy efficiency for fast operation of SAR ADCs, rail-to-rail dynamic latch comparator with modified adaptive power control (APC) is implemented. The proposed ADC structure has been implemented in 130 nm CMOS process. The ADC has an effective number of bit (ENOB) of 10.97 bits while consuming 7.08 mW current consumption from the 1.2 V supply voltage.