This article presents a high-efficiency fast transient constant on -time (COT) control dc–dc buck converter for the Internet of Things applications. The current reused current sensor is proposed to enhance the loop stability and improve the power conversion efficiency at light load. Input current is sensed and added to the feedback voltage of the dc–dc converter to increase the sensed output ripple voltage. Fast transient dc-offset cancelation technique is introduced to achieve a fast transient recovery time and to cancel the output dc offset. This chip is fabricated with a 0.13- μ m CMOS process. A standard supply voltage of 7–15 V is applied to produce the output voltage of 5–5.33 V. The total die area is 2 mm × 1.5 mm. The settling time is 17 μ s. The transient recovery time from light to heavy load and from heavy load to light load are 3 μ s and 2.7 μ s, respectively, with a maximum dc offset of 3.5 mV. The overshoot voltage is 85 mV and the undershoot voltage is 72 mV. The peak efficiency of the proposed design is 95.56% at 0.5 A and efficiency at the light load of 10 mA is 84.60%.
6 April 2021 in IEEE Transactions on Power Electronics
This article presents a power-efficient hybrid energy-harvesting system that scavenges energy from solar, vibration, and radio frequency (RF) energy sources and converts into regulated output dc voltage courtesy buck–boost dc–dc converter. The proposed architecture incorporates tetra-paths for maintaining high power conversion efficiency (PCE) over extended input power range (−10 to 30 dBm). A time-domain maximum power point tracking technique is proposed for solar energy harvester. A high-efficiency full wave rectifier is designed for triboelectric rectifier. A 5.8-GHz RF-dc converter with adaptive matching is proposed to increase dynamic range of the input power. The chip is implemented in 0.18-µm bipolar-CMOS-DMOS process. The die area of the chip is 2.8 mm × 5.0 mm, including the pads. The solar and triboelectric energy harvesters achieve a measured peak efficiencies of 75.4% and 92.3%, respectively. The high-power 5.8-GHz RF-dc converter achieves measured PCE of 76% at 30 dBm input power. The low-power dual-band RF-dc converter operating at 900 MHz and 2.4 GHz obtains measured peak efficiencies of 73% and 71.9% at 0 dBm input, respectively. The buck–boost dc–dc converter employed in the proposed hybrid energy harvesting system achieves a measured peak PCE of 94.5%.
Recently, piezoresistive-type (PRT) pressure sensors have been gaining attention in variety of applications due to their simplicity, low cost, miniature size and ruggedness. The electrical behavior of a pressure sensor is highly dependent on the temperature gradient which seriously degrades its reliability and reduces measurement accuracy. In this paper, polynomial-based adaptive digital temperature compensation is presented for automotive piezoresistive pressure sensor applications. The non-linear temperature dependency of a pressure sensor is accurately compensated for by incorporating opposite characteristics of the pressure sensor as a function of temperature. The compensation polynomial is fully implemented in a digital system and a scaling technique is introduced to enhance its accuracy. The resource sharing technique is adopted for minimizing controller area and power consumption. The negative temperature coefficient (NTC) instead of proportional to absolute temperature (PTAT) or complementary to absolute temperature (CTAT) is used as the temperature-sensing element since it offers the best temperature characteristics for grade 0 ambient temperature operating range according to the automotive electronics council (AEC) test qualification ACE-Q100. The shared structure approach uses an existing analog signal conditioning path, composed of a programmable gain amplifier (PGA) and an analog-to-digital converter (ADC). For improving the accuracy over wide range of temperature, a high-resolution sigma-delta ADC is integrated. The measured temperature compensation accuracy is within ±0.068% with full scale when temperature varies from −40 °C to 150 °C according to ACE-Q100. It takes 37 µs to compute the temperature compensation with a clock frequency of 10 MHz. The proposed technique is integrated in an automotive pressure sensor signal conditioning chip using a 180 nm complementary metal–oxide–semiconductor (CMOS) process.
18 September 2020 in IEEE Transactions on Power Electronics
In this article, a 15-W quadruple-mode reconfigurable wireless power-receiving unit with high efficiency for Inductive coupling and magnetic resonance-based standards, such as wireless power consortium (WPC), power matters alliance (PMA), alliance for wireless power (A4WP), and magnetic secure transmission (MST) applications is proposed. Quadruple-mode gate controller(QMGC) is proposed in quadruple-mode synchronous rectifier to manage sizes of core and drivers which results in maximum power conversion efficiency (PCE) for each mode based on conduction and switching losses. In QMGC, switchable zero voltage and current sensing block is proposed for WPC/PMA to maximize PCE regardless of load current variations. For A4WP mode, a digitally controlled delay adjustment block is adapted to minimize power consumption while compensating for delay which results in reverse leakage current and power loss. Finally, for MST mode, low power TX (LPTX) block is implemented to minimize current consumption so that burden on battery can be minimized. A high-resolution current sensor is proposed in low-drop out regulator to sense current for overcurrent limit and overcurrent protection. The measured PCE of proposed system at 15 W are 95.3% and 92.3% for WPC/PMA and A4WP mode, respectively. For MST, power consumption is reduced to 35% courtesy LPTX block.
1 October 2021 in IEEE Transactions on Industrial Electronics
This paper presents a 0.46 mW and 2.4 GHz; All-Digital Phase-Locked Loop (ADPLL) through an Injection-Locked Frequency Multiplier (ILFM) and Continuous Frequency Tracking Loop (CFTL) circuitry for low power Internet-of-Thing (IoT) applications. In the proposed ADPLL architecture to save power, the need for Time-to-Digital Converter (TDC) is eliminated through providing the CFTL circuitry. This feature makes the design compact, low power, and suitable for IoT applications. The proposed design is based on a synthesizable pulse injection and frequency-locked loop along with an ultra-low-power LC Digitally-Controlled Oscillator (LC-DCO). The presented CFTL circuit adjusts the frequency of the DCO continuously and prevents the frequency drift after the reference injection. Inside the designed LC-DCO core, the power consumption is minimized by optimizing the $\text{g}_{\mathrm {m}}~/\text{I}_{\mathrm {D}}$ and adjusting the power supply to 0.5 V. The proposed ILFM based ADPLL is fabricated in 55 nm CMOS technology and covers the operational frequency range of 2.402 GHz to 2.480 GHz with a reference frequency of 32 MHz. The measured phase noise performance of the ADPLL is −111.15 dBc/Hz at 1 MHz offset frequency from the carrier frequency of 2.4 GHz. It consumes only 0.46 mW power with an active area of 0.129 mm 2 .