At global level, there is a continuing concern for the research and development of alloys for medical and biomedical applications. Metallic biomaterials are used in various applications of the most important medical fields like orthopedic, dental and cardiovascular. The main metallic biomaterials used in human body are stainless steels, Co-based alloys and Ti-based alloys. Titanium and its alloys are of greater interest in medical applications because they exhibit characteristics required for implant materials, namely, good mechanical properties (less elasticity modulus than stainless steel or CoCr alloys, fatigue strength, high corrosion resistance), high biocompatibility. The aim of this review is to describe and compare the main characteristics (mechanical properties, corrosion resistance and biocompatibility) for latest research of nontoxic Ti alloys biomaterials used for medical field.

The performance of the field and the condition of success in oral implantology today require the review and reevaluation of the means that contribute essentially to ensuring the stability and durability of the implant, starting from the nature of the biomaterial and continuing with the characteristics of the optimally designed biosurface. This paper proposes a comparative analysis of three commercial alloys, VeraBond, Kera N, and VeraSoft, compared to a modified dental alloy, with the aim of improving some mechanical properties. They have been studied structurally and mechanically. The microstructural structure shows that the alloys crystallize in the face-centered cube system, and the cast alloy has a dendritic structure with large grains. XRD diffractograms highlight that alloys exhibit three compounds Cr156.00 Al596.00: 9013031, Ni4.00, and Cr30.00Al48.00. The hardness measurements showed values between 203 HV and 430 HV. As the percentage of silicon increases, the hardness decreases. The modulus of elasticity obtained by the indentation method for the dental alloys was in the range of 46–153 GPa. The results showed that the hardness and elastic modulus of the new alloy was significantly minimized compared to the classical alloys used.

Ceramic coatings have many advantages for industrial and medical applications due to their exceptional properties. Ceramic coatings with a thickness of approximately 45 μm, after grinding, were grown using a robotic arm that used the atmospheric plasma spraying procedure. The thermal shock stresses—a common situation in applications but difficult to reproduce under laboratory conditions—of the ceramic layers on top of the metal substrate was achieved using solar energy focused by a concentrating mirror, based on experiments conducted in the CNRS-PROMES laboratory, UPR 8521, belonging to the French National Centre for Scientific Research (CNRS). The ceramic layers showed excellent stability at 1000 °C, even at high heating or cooling rates. At high temperatures (above 1800 °C), the exfoliation of the complex ceramic layer was observed. No differences in the structural, phase, mechanical or adhesion properties of the ceramic layer were observed after the thermal shock cycles (in the literature, there have been quite few reports regarding the properties of the ceramic layers after the thermal shock application). Scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), atomic force microscopy (AFM) and X-ray diffraction (XRD) techniques were used to characterize the complex ceramic coating and the effects of thermal shock cycling. The phases and chemical composition of the complex coatings remained similar, insensitive to thermal shock at 1000 °C, consisting of a mixture of crystalline yttrium zirconium oxide and α and γ alumina. For all cases, the main residual stress state was tensile. After 5 or 10 cycles of thermal shocks, a smoothing of the residual stress state was observed in the investigated area. A higher temperature (above 1800 °C), applied as thermal shock, led to higher residual stresses and resulted in large cracks and the spallation of the coating layer.

The influence of the chemical composition and structural state of Zn–Ti alloys on corrosion behaviour and mechanical properties was studied. Zn-based alloys were investigated, more precisely, pure technical Zn and Zn with 0.10, 0.25 and 1.00 wt.% Ti. The microstructure and chemical composition of these materials were analysed using light optical microscopy (LOM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The chemical composition of the alloys and the surface after immersion were analysed using an EDS detector from Bruker. The alloys’ electro-chemical corrosion resistance was further investigated through linear (LP) and cyclic (CP) potentiometry and open-circuit potential (OCP) analysis. A tensile/compression equipment (Instron 34SC-5) was used to determine the compression behaviour. UMT testing equipment was used to determine microhardness (by Rockwell indentation) and COF vs. length. For percentages higher than 0.25 wt.% Ti, the formation of a primary TiZn₁₆ intermetallic compound in the (α-Zn + TiZn₁₆) eutectic matrix was observed, a slight influence of TiZn₁₆ on the Zn corrosion resistance results, and a greater influence on the mechanical properties was confirmed.