13-kV 4H-SiC MOSFETs were successfully fabricated on a 125-μm-thick epitaxial layer on 6-in, N+ SiC substrates. Both lateral and longitudinal straggles from the P-well implant were investigated to optimize the JFET width and thus to avoid channel pinching in the JFET region. Channel lengths and channel mobilities were varied to investigate the effect of channel portions in determining the on-state resistance of the 13-kV MOSFETs. It was discovered that the low channel mobility limits the transconductance, such that the MOSFETs cannot offer full current at reasonable gate voltages (Vgs = ~ 20 V). Even in high voltage MOSFETs, it is essential to have a reasonably high channel mobility to reduce on-state power loss. Therefore, channel design and process are also important aspects of high voltage devices. A superior blocking capability of 13.2 kV was demonstrated using a ring-based edge termination structure. It is important to note that the straggling effect due to ion implantations should also be taken into account when designing an edge termination structure. Static electrical characteristics, scanning electron microscope (SEM) imaging, secondary ion mass spectrometry (SIMS) analysis, and 2-D simulation of the 13-kV MOSFETs were employed to support this reasoning.
20 January 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This article presents the short-circuit (SC) capability evaluation of TO-247-3 packaged silicon carbide (SiC) metal–oxide–semiconductor field-effect transistors (MOSFETs) based on tests under different drain biases and gate biases. Compared with the 900-V Si super-junction MOSFET and the 1200-V Si trench-gate field-stop insulated gate bipolar transistor (IGBT), SiC devices show higher saturation current per die area, which requires more rigorous chip design consideration to reach an acceptable SC withstand time (SCWT). The test results also reveal that the SC withstand capability of SiC MOSFETs can still be enhanced. Thus, in both chip design and detection circuits, several novel approaches investigated in recent years, which could potentially improve SC ruggedness of SiC device-based systems, are discussed at the end of this article.
This article provides a detailed study of performance and reliability issues and trade-offs in silicon carbide (SiC) power MOSFETs. The reliability issues such as threshold voltage variation across devices from the same vendor, instability of threshold voltage under positive and negative gate bias, long-term reliability of gate oxide, screening of devices with extrinsic defects by means of gate voltage, body diode degradation, and short circuit withstand time are investigated through testing of commercial devices from different vendors and two-dimensional simulations. Price roadmap and foundry models of SiC MOSFETs are discussed. Future development of mixed-mode CMOS circuits with high voltage lateral MOSFETs along with 4−6× higher power handling capability compared to silicon circuits has been described.
Metal, typically gold [Au], nanoparticles [NPs] embedded in a capping metal contact layer onto silicon carbide [SiC] are considered to have practical applications in changing the barrier height of the original contacts. Here, we demonstrate the use of silver [Ag] NPs to effectively lower the barrier height of the electrical contacts to 4H-SiC. It has been shown that the barrier height of the fabricated SiC diode structures (Ni with embedded Ag-NPs) has significantly reduced by 0.11 eV and 0.18 eV with respect to the samples with Au-NPs and the reference samples, respectively. The experimental results have also been compared with both an analytic model based on Tung's theory and physics-based two-dimensional numerical simulations.
In this paper, the results of electrical reliability measurements of commercially available 1200 V Silicon Carbide (SiC) MOSFETs are reported. The threshold voltage shift caused by interface states and the trapped charges near the SiC/SiO 2 interface is observed under positive and negative DC-bias-stress over 50 hours. Threshold voltage reduction with temperature is also reported for devices from different vendors. Negative shift of subthreshold characteristics under the negative bias stress and high drain bias at elevated temperature indicates that the threshold voltage of the devices should be increased by at least 1–2 V. Extracted interface state density using subthreshold $I-V$ curves indicates very different SiC/SiO 2 interface for devices from different vendors.
In this study, nano-scale honeycomb-shaped structures with anti-reflection properties were successfully formed on SiC. The surface of 4H-SiC wafer after a conventional photolithography process was etched by inductively coupled plasma. We demonstrate that the reflection characteristic of the fabricated photodiodes has significantly reduced by 55% compared with the reference devices. As a result, the optical response Iillumination/Idark of the 4H-SiC photodiodes were enhanced up to 178%, which can be ascribed primarily to the improved light trapping in the proposed nano-scale texturing.