The cold powering test of the first two prototypes of the MQXFB quadrupoles (MQXFBP1, now disassembled, and MQXFBP2), the Nb 3 Sn inner triplet magnets to be installed in the HL-LHC, has validated many features of the design, such as field quality and quench protection, but has found performance limitations. In fact, both magnets showed a similar phenomenology, characterized by reproducible quenches in the straight part inner layer pole turn, with absence of training and limiting the performance at 93% (MQXFBP1) and 98% (MQXFBP2) of the nominal current at 1.9 K, required for HL-LHC operation at 7 TeV. Microstructural inspections of the quenching section of the limiting coil in MQXFBP1 have identified fractured Nb 3 Sn sub-elements in strands located at one specific position of the inner layer pole turn, allowing to determine the precise origin of the performance limitation. In this paper we outline the strategy that has been defined to address the possible sources of performance limitation, namely coil manufacturing, magnet assembly and integration in the cold mass.
31 March 2023 in IEEE Transactions on Applied Superconductivity
By the end of October 2022, the US HL-LHC Accelerator Upgrade Project (AUP) had completed fabrication of ten MQXFA magnets and tested eight of them. The MQXFA magnets are the low-beta quadrupole magnets to be used in the Q1 and Q3 Inner Triplet elements of the High Luminosity LHC. This AUP effort is shared by BNL, Fermilab, and LBNL, with strand verification tests at NHMFL. An important step of the AUP QA plan is the testing of MQXFA magnets in a vertical cryostat at BNL. The acceptance criteria that could be tested at BNL were all met by the first four production magnets (MQXFA03-MQXFA06). Subsequently, two magnets (MQXFA07 and MQXFA08) did not meet some of the criteria and were disassembled. Lessons learned during the disassembly of MQXFA07 caused a revision to the assembly specifications that were used for MQXFA10 and subsequent magnets. In this article, we present a summary of: 1) the fabrication and test data for all the MQXFA magnets; 2) the analysis of MQXFA07/A08 test results with characterization of the limiting mechanism; 3) the outcome of the investigation, including the lessons learned during MQXFA07 disassembly; and 4) the finite element analysis correlating observations with test performance.
23 January 2023 in IEEE Transactions on Applied Superconductivity
The design and production of Nb 3 Sn-based dipole and quadrupole magnets is critical for the realization of the High-Luminosity Large Hadron Collider (HL-LHC) at the European Organization for Nuclear Research (CERN). Nb 3 Sn superconducting coils are aimed at enhancing the bending and focusing strengths of accelerator magnets for HL-LHC and beyond. Due to the brittle nature of Nb 3 Sn, the coil fabrication steps are very challenging and require very careful QA/QC. Flaws in the Nb 3 Sn filaments may lead to quenches, and eventually, performance limitation below nominal during magnet testing. A novel inspection method, including advanced non-destructive and destructive techniques, was developed to explore the root-causes of quenches occurring in performance-limiting coils. The most relevant results obtained for MQXF coils through this innovative inspection method are presented. This approach allows for precise assessment of the physical events associated with the quenches experienced by magnet coils, mainly occurring in the form of damaged strands with transversely broken sub-elements. Coil-slice preparation, micro-optical observations of transverse and longitudinal cross-sections, and a deep etching technique of copper will be illustrated in the present work, with a focus on the results achieved for a CERN coil from a non-conforming quadrupole magnet prototype, and two coils fabricated in the US, in the framework of the Accelerator Upgrade Project (AUP) collaboration, from two different non-conforming quadrupole magnets, respectively. The results obtained through the proposed inspection method will be illustrated.
6 February 2019 in IEEE Transactions on Applied Superconductivity
The 11 T magnet and other high-field magnets in the framework of the High-Luminosity LHC (HL-LHC) project, are based on epoxy resin impregnated $Nb_{3}Sn$ coils. This paper presents the development of an experimental measurement set-up, and associat-ed methodology for the determination of the mechanical proper-ties in compression of epoxy resin impregnated $Nb_{3}Sn$ coils. The challenges addressed include the non-linear compliance correction in complex compression testing. The application of these techniques are demonstrated by the experimental characterization of the compression behavior of 11 T coils.
6 February 2024 in IEEE Transactions on Applied Superconductivity
The ITER Thermal Shields (TS) consist of actively cooled stainless steel panels. Their role is to minimise the radiation heat load from warm components, such as the Vacuum Vessel (VV) and the cryostat, hence contributing to insulating the magnet system operating at 4.5 K. The panels, cooled by 304L stainless steel pipes stitch welded to 10 mm to 20 mm thick 304LN plates, were coated by a low emissivity silver layer following welding of the pipes and bending operations. Pressurised He gas flows in the pipes at a temperature of 80 K and a pressure of 1.8 MPa at the inlet. These components have been manufactured and delivered to IO and their assembly had been started. Three leaks were detected in Helium leak tests during site acceptance test of the TS. A failure analysis was carried out based on advanced non-destructive and destructive examination techniques, including X-ray microtomography and Focused Ion Beam - Scanning Electron Microscopy (FIB-SEM), confirming crack initiations of different severities, in particular presence of multi-branched “lightning bolt” transgranular cracks through the thickness of the pipes and of corrosion residues featuring high chlorine content. The root cause of the leakages has been univocally associated to Stress Corrosion Cracking (SCC), initiated by halide residues from the silver coating process in combination with the stress induced by the attachment, by welding, of the pipes to the plates. The paper summarises the results of these investigations and the lessons learned, the remedial actions implemented and the planned repair/replacement solutions.
9 February 2022 in IEEE Transactions on Applied Superconductivity
In the quest for higher field accelerator superconducting magnets, essential parts of their design are the so called yokes, which are traditionally made of low – carbon magnetic steel. In currently used magnets, they are typically found in the form of fine – blanked laminations, or machined from laminated heavy plates. The material’s choice is made based on a compromise between the high saturation field, providing a return path for the magnetic flux, and the mechanical robustness conferred to the magnets’ cold masses. This paper describes the mechanical characterization of low – carbon steel, and applies several approaches for the design and validation of the material from the structural point of view, applicable to a Nb $_{3}$ Sn quadrupole: MQXF. Tensile tests at room and cryogenic temperatures, together with fatigue and fracture toughness at cryogenic temperature have been performed. Calculations based on the obtained material properties and results of extensive non-destructive examination (ultrasonic testing) have been implemented in order to ascertain the structural limits of low – carbon steel for its use in the fabrication of high field accelerator superconducting magnets.