Chemically reversible hydrogels: The dynamic reorganization of some cellular biopolymers in response to signals has inspired efforts to create artificial materials with similar properties. Freeman et al. created hydrogels based on peptide amphiphiles that can bear DNA strands that assemble into superstructures and that disassemble in response to chemical triggers. The addition of DNA conjugates induced transitions from micelles to fibers and bundles of fibers. The resulting hydrogels were used as an extracellular matrix mimic for cultured cells. Switching the hydrogel between states also switched astrocytes between their reactive and naïve phenotypes. Science , this issue p. 808
Red micro-light-emitting diodes (μLEDs) have been generated significant interest for the next generation μLEDs displays. It has been shown that the external quantum efficiency (EQE) of AlInGaP red μLEDs markedly decreases as the size goes to very small dimension. Here, we demonstrate size-independent peak EQE of 611 nm InGaN red μLEDs. Packaged μLEDs show a peak EQE varied from 2.4% to 2.6% as the device area reduces from 100 × 100 to 20 × 20 μm2. These results demonstrate the promising potential for realizing high efficiency red μLED with very small size using InGaN materials.
In this study, two methods to tune the emission wavelength of micro-LEDs fabricated on tile patterned compliant GaN-on-porous-GaN pseudo-substrates (PSs) are presented. The mechanical flexibility of porous GaN was utilized to relax the strain induced during the growth of light-emitting diode (LED) structures with n- and p-InGaN layers and enhance the indium incorporation via the composition pulling effect. The first approach involved only varying the size of the PS square tiles used for LED structure regrowth, from 20 × 20 μm2 to 8 × 8 μm2. Higher n-InGaN base layer relaxation with decreasing tile size resulted in a red shift of emission from 525 nm to 561 nm with no change in the growth conditions. The second method involved changing the mole fraction, x, of the n-InxGa1−xN base layer of the LED structure from 0.04 to 0.09 by reducing growth temperature, while maintaining the high temperature growth conditions of the multi-quantum well (MQW) and p-InGaN targeting 530 nm emission. The resulting wavelength shift was a remarkable 536–616 nm due to the stronger composition pulling effect, providing a pathway to enable high indium content MQW active regions to be grown at high temperature.
We present efficient red InGaN 60 × 60 μm2 micro-light-emitting diodes (μLEDs) with an epitaxial tunnel junction (TJ) contact. The TJ was grown by metal-organic chemical vapor deposition using selective area growth. The red TJ μLEDs show a uniform electroluminescence. At a low current density of 1 A/cm2, the emission peak wavelength is 623 nm with a full-width half maximum of 47 nm. The peak external quantum efficiency (EQE) measured in an integrating sphere is as high as 4.5%. These results suggest a significant progress in exploring high efficiency InGaN red μLEDs using TJ technology.
We study the high-temperature electroluminescence properties of 600 nm InGaN red 40 × 40 μm2 micro-light-emitting diodes (μLEDs) with a peak external quantum efficiency (EQE) of 3.2%. Temperature-dependent peak wavelength measurements show a low redshift of 0.05 nm/K. The injection efficiency improves with increasing temperature. The hot/cold (HC) factor is used to quantify the thermal droop: at 400 K, the EQE and wall-plug efficiency HC factors at 50 A/cm2 reach high values of 0.72 and 0.85, respectively. This demonstrates the robustness of InGaN red μLEDs up to high temperature, with a much-improved stability over conventional AlInGaP red μLEDs.
In this paper, we report the successful demonstration of bright InGaN-based microLED devices emitting in the red spectral regime grown by metal organic chemical vapor deposition (MOCVD) on c-plane semi-relaxed InGaN substrates on sapphire. Through application of an InGaN/GaN base layer scheme to ameliorate high defect density and maintain appropriate lattice constant throughout the growth, high-In quantum wells (QWs) can be grown with improved crystal quality. Improvement to the design of the growth scheme also yields higher power output resulting in an increase to the external quantum efficiency (EQE). Combined, these two improvements allow for an 80 × 80 m microLED device emitting at 609 nm to achieve 0.83% EQE. Furthermore, the true In content of the QW is measured using atomic probe tomography (APT) to confirm the improved In incorporation during high temperature active region growth. These developments represent advancement toward the realization of bright, highly efficient red III-nitride LEDs to be used in RGB applications under one material system.