10 February 2020 in IEEE Electron Device Letters
In this work, fast sweeping characterization with an extremely short relaxation time was used to probe the VTH instability of p-GaN gate HEMTs. As the ID-VG sweeping time deceases from 5 ms to 5 μs, the VTH dramatically degenerates from 3.13 V to 1.76 V, meanwhile the hysteresis deteriorates from 22.6 mV to 1.37 V. Positive bias temperature instability (PBTI) measurement by fast sweeping shows the VTH features a very fast shifting process but a slower recovering process. D-mode HEMTs counterpart without Mg contamination demonstrates a negligible VTH shift and hysteresis, proving the VTH instability is probably due to the ionization of acceptor-like traps in the p-GaN depletion region. Finally, the VTH instability is verified by a GaN circuit under switching stress. The VTH instability under different sweeping speed uncovers the fact that the high VTH by conventionally slow DC measurements is probably artificial. The DC VTH should be high enough to avoid HEMT faulty turn-on.
16 October 2020 in IEEE Transactions on Power Electronics
In this letter, the dynamic R on degradation mechanisms of the p-GaN gate HEMTs induced by off-state stress are investigated with different passivation dielectrics AlON and SiN. The degradation mechanisms are twofold, including V TH shift and surface trapping in the gate-to-drain access region, whose impacts are successfully distinguished. Surface trapping by SiN passivation is evidently proved to be the dominant factor that can almost induce a full current collapse. The V TH positive shift diminishes the drain current by shrinking the overdrive V GS , which however, can be compensated by a higher V GS overdrive in applications. SiN passivation can effectively suppress the positive bias temperature instability effect, probably by passivating the p-GaN fast traps with hydrogen during passivation. Last, the transient measurements unveil that both the surface trapping and V TH shift have a very slow recovery process.
27 May 2021 in IEEE Transactions on Electron Devices
A comprehensive investigation on the hot-carrier-induced interface state generation and its impact on carrier mobility in nMOSFET is performed. I-V compact modeling and charge pumping (CP) characterization are used as independent ways to evaluate the interface state density as a function of hot-carrier-induced aging. From the two techniques, similar power-law time exponents of the interface state density kinetics are obtained. Assisted by the quasi-spectroscopic (temperature-resolved) CP measurement, the extracted interface state density is further correlated with the I-V modeling results: an universal mobility degradation normalization parameter Nit,ref = ~, 4.1 x 10¹¹/cm² is reported, irrespective of the effective oxide thickness (EOT), stress temperature, or the relative degradation of the device under test (DUT). Supported by the fundamental principles deployed in the derivation and the broad range of experimental conditions considered for its validation, the reported normalization parameter could serve as a modeling constant in the commonly used I-V compact models to correlate the mobility degradation with the interface state density induced by hot carrier stress.
25 April 2019 in IEEE Transactions on Device and Materials Reliability
We investigate BTI charge trapping trends in high-k metal gate (HKMG) stacks with a variety of work function metals. Most BTI models suggest charge trapping in oxide defects is modulated by the applied oxide electric field, which controls the energy barrier for the capture process, irrespective of the gate work function. However, experimental data on capacitors show enhanced or reduced charge trapping at constant oxide electric field for different work function metal stacks. We ascribe this to a different chemical interaction of the metals with the dielectric, which yields different defect profiles depending on the process thermal budget, and not to the gate work function per se. This observation is confirmed by comparing BTI degradation in nMOS and pMOS Replacement Gate planar transistors with three selected work function metal stacks (representative of high-, standard, and low-Vth device flavors), and two different process thermal budgets. Furthermore, by employing the imec/T.U. Wien physics-based BTI simulation framework “Comphy”, we also show that, on top of the unavoidable chemical interaction of different metals with the underlying SiO2/HfO2 dielectric stack, different gate work functions within a typical range of relevance (4.35-4.75eV) can yield a different charge state of the deep high-k defects, and can therefore have an impact on charge trapping kinetics during BTI stress, particularly in nMOSFETs.